TL;DR — Direct answer: A solar water heater plant typically runs 7 to 8 bar, 5 to 12 m3/min, on 37 to 90 kW rotary screw compressors, with a 3°C pressure dew point dryer and 0.01 micron filtration protecting tank welding, absorber coating and water testing from moisture and oil. QiAir, a Chinese screw compressor manufacturer and supplier, sizes systems with clean, stable air so enamel and coating lines never suffer a defect.

Solar water heaters look simple from the outside, but their factory is a demanding place for compressed air. Stainless and enamelled tanks are welded and pressure-tested, absorber plates are coated with selective surfaces, and glass tubes are handled, assembled and packed in the same building. Each step needs air that is dry, clean and always there.

Industrial screw air compressor
Industrial screw air compressor

The product lives on a roof for twenty years, so a coating defect or a weak weld made today becomes a leak or a rust spot years later. Air quality at the coating line and the welding station is therefore a warranty issue, and buyers who audit the factory will ask about it directly.

Tank Welding, Rolling and Enamel Preparation

Tank welding is the heaviest air load in a solar heater plant. Plasma cutting shapes the steel, rolling forms the cylinder, and circumferential welding joins the shell, with pneumatic clamps and positioners holding the tank at every step. A pressure sag during a weld changes the fit-up gap, and the welder then fights the joint instead of welding it.

Enamel preparation is where air quality decides the product life. Tanks are blasted clean before enamelling, and the blasting air must be dry and oil-free, because a single oil spot under the enamel becomes a rust point that breaks through years later. Give the blasting station a dedicated dryer and filtration set, and test the air for oil carryover every month.

Water testing after welding is the gate every tank must pass. The tank is filled and pressurised, and the test watches for leaks at every seam, so the air used to drive the test pumps and valves must be clean and dry. A wet test line can leave moisture inside a tank that is then sealed and shipped, starting corrosion before the heater ever reaches a roof.

  • Hold 7 bar steady at welding and rolling stations
  • Dry blasting air and test it for oil carryover monthly
  • Keep test-pump air clean and dry at all times

Absorber Coating, Glass Tubes and Assembly

Absorber plates carry a selective coating that absorbs sunlight and rejects heat loss, and the coating line is the cleanest corner of the plant. Spray guns and coating heads need air filtered to 0.01 micron with carbon adsorption, dried to a low dew point, and regulated to a steady 6 bar, because a pressure wobble changes the coating thickness and the thermal performance.

Glass vacuum tubes are handled on air-powered equipment that must be gentle as well as reliable. Suction cups lift the tubes, air cushions move them between stations, and a sudden pressure drop can crack a tube or drop it onto the line.

Assembly lines bring the tank, the absorber and the frame together. Pneumatic screwdrivers, riveters and presses cycle all day, and their combined demand peaks when several lines start a batch together. A variable-speed drive compressor follows those peaks without cycling, and the assembly crew never waits for air to recover between machines.

  • Give absorber coating its own desiccant dryer and carbon filter
  • Fit a local receiver at glass-tube handling stations
  • Use a VSD compressor for spiky assembly-line loads

Water Testing, Packaging and Outdoor Storage

Finished heaters are water-tested before packing, and the test rigs use air for valve actuation and for blowing water out of the circuits afterwards. Residual water left in a heater that is then stored outdoors can freeze and crack a joint, so the blow-out air must be dry and the drying cycle long enough to clear every low point in the pipework.

Packaging lines run fast and use air everywhere. Carton erectors, strapping machines and labelling heads cycle hundreds of times per hour, and a slow cylinder jams the line at the worst moment. The load is steady rather than spiky, so keep packaging on a regulated branch and the main header stays free for the welding and coating peaks.

Outdoor storage of finished stock adds a seasonal problem. Heaters stored outside in humid weather need their ports capped and their circuits kept dry, and the factory air system must cope with summer humidity that pushes the dryer to its limit. Check the dryer dew point weekly in summer, and never let a clogged drain trap flood the air lines.

  • Blow out test water with dry air before packing
  • Keep packaging air on a regulated branch
  • Check the dryer dew point weekly in summer humidity

Buying from China: Sizing Sheet for Solar Heater Plants

Before requesting a quotation, gather four numbers: the tank welding and blasting peak flow, the absorber coating air quality specification, the glass-tube handling and assembly load, and the distance from the compressor room to the furthest coating booth. A supplier that quotes from the heater output alone will miss the coating specification entirely.

For most solar water heater plants the practical range is a 37 to 75 kW variable-speed drive screw compressor at 7.5 or 8 bar, with a refrigerated dryer, 0.01 micron filtration, carbon adsorption and a 2,000 to 3,000 litre receiver. Larger plants with several coating lines usually run a duty-plus-standby pair so maintenance never stops a production run.

When comparing Chinese suppliers, ask for the full package price including dryer, filters, receiver and commissioning spares, and confirm the export packing, voltage and documentation for your country. Check the filter element life, the service interval and the availability of filters and airends through the supplier's export channel. QiAir, a Chinese screw compressor manufacturer and supplier, quotes the complete package so buyers compare real installed cost.

  • Collect welding, coating and assembly loads before quoting
  • Budget 37 to 75 kW VSD plus dryer and carbon filtration
  • Confirm spares, voltage and export packing in writing

Frequently asked questions

What pressure does a solar water heater plant normally run?

Most run 7 to 8 bar at the header, with welding at 7 bar, blasting above 6.5 bar at the nozzle, and absorber coating regulated to a steady 6 bar.

Why is oil in blasting air so harmful for enamelled tanks?

An oil spot under the enamel becomes a rust point that breaks through years later on a roof. Blasting air must be dry and oil-free, tested for carryover every month.

Does absorber coating need special air treatment?

Yes. The selective coating needs air filtered to 0.01 micron with carbon adsorption and dried to a low dew point, on its own branch separate from welding and blasting air.

Should test water be blown out with compressed air?

Yes, with dry air, and long enough to clear every low point. Residual water left in a heater stored outdoors can freeze and crack a joint before installation.

Related reading

QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.