TL;DR — Direct answer: A spring factory needs clean, dry air at 6 to 8 bar for wire coiling, heat treatment, shot peening, grinding and coating, with a 3 degree C pressure dew point and 0.01 micron filtration. Size on the coincident peak of the coiling machines and the peening line, 4 to 8 cubic metres per minute, roughly a 30 to 55 kW screw compressor with a variable speed drive. QiAir, a Chinese screw compressor manufacturer and supplier, builds machines with dry-air treatment for spring factories.
A spring is a precision component, and its factory runs on fast, repeating air demands. Wire is coiled on CNC machines, heat treated in furnaces, shot peened for fatigue resistance, ground at the ends, and coated before packing. Compressed air drives coiler feed and cut-off, furnace controls, peening nozzles, grinding spindles and the coating line. A pressure dip at the coiler changes spring pitch, moisture rusts a freshly peened surface, and oil stops a coating from bonding. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for spring plants are specified around stable pressure and dry air first.

The common sizing mistake is counting the coiling machines alone and forgetting shot peening. Coilers draw air in short pulses at every cut-off, heat treatment is a steady control load, and the peening line draws a heavy, continuous flow while it runs. This guide maps where the air goes, explains how to size for coiling and peening peaks, sets the dry-air standard that protects spring steel, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: Coiling, Heat Treatment, Shot Peening and Grinding
CNC coiling machines are the most sensitive users. Wire feed, pitch control, cut-off and mandrel clamping all run on air, pulsing with every spring produced, several times a minute on a fast machine. A pressure dip at the cut-off leaves a rough spring end, and a dip in pitch control changes the spring rate. Keep pressure at the coiler within a narrow band, with a dedicated filter and regulator close to each coiling group.
Heat treatment, shot peening, grinding and coating take the rest. Furnaces use air for dampers, burners and quench controls, peening lines use it for media blasting nozzles and part handling, grinders use it for spindle cooling and end-face grinding, and coating lines use it for spray guns. Peening is the heaviest single user: a cabinet running continuously can draw 2 to 4 cubic metres per minute on its own.
- CNC coiling: wire feed, pitch control, cut-off and mandrel clamping pulsing with every spring.
- Heat treatment: furnace dampers, burner controls and quench systems that need stable pressure.
- Shot peening and grinding: media blasting nozzles, part handling, spindle cooling and end-face grinding.
Sizing for Coiling Pulses and Peening-Line Demand
List every machine with its flow at peak and at steady running. A mid-size plant with six to twelve coiling machines, two furnaces and one or two shot peening lines typically peaks at 4 to 8 cubic metres per minute at 6 to 8 bar, roughly a 30 to 55 kW screw compressor, with the peak landing when the peening line runs at full load while several coilers cut off together. A variable speed drive follows the fast coiling pattern instead of loading and unloading a fixed-speed machine dozens of times a shift.
Keep the pressure drop to the farthest coiling machine under 0.3 bar at peak flow, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb cut-off and peening spikes. Log pressure at the farthest coiler for a week of full production: that log is the honest record of whether the compressor is big enough.
- Size on the coincident peak of the coiling machines and the shot peening line, not on coiling alone.
- Use a variable speed drive for fast coiling pulses, and keep far-end pressure drop under 0.3 bar.
- Log farthest-coiler pressure during production for a week to prove the sizing in real use.
Dry Air for Spring Steel: Preventing Rust and Coating Failure
Moisture is the main enemy in spring manufacturing. Freshly peened spring steel rusts quickly, a damp spring stored before coating develops surface rust the coating cannot hide, and moisture in a coiling valve causes sticking and pitch drift. The fix is a treatment chain: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour, with a final point-of-use filter at each coiling group. In humid climates, a desiccant dryer to minus 20 degrees C is worth the extra cost.
Oil is the second risk: oil on a spring before coating stops the coating from bonding, and oil in a peening nozzle contaminates the media and the spring surface. Keep the compressor room clean, ventilated and cool, drain condensate with automatic zero-loss drains, and test air at the farthest coiler quarterly. Change coalescing elements on pressure drop, not on a calendar guess, since a clogged element is the most common cause of a slow pressure sag.
- Fit pre-filter, refrigerated dryer, 0.01 micron coalescing filter and carbon filter, with a final filter at each coiling group.
- Consider a desiccant dryer to minus 20 degrees C where springs are stored before coating in humid climates.
- Drain condensate automatically, and test air at the farthest coiler quarterly for oil and moisture.
Buying from China: Sizing Sheet for a Spring Factory Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and a spring order should start with a sizing sheet that names the machine count. Send the supplier the number of coiling machines, furnaces and shot peening lines, the coincident peak at 6 to 8 bar, the air-quality standard the coilers and peening nozzles require, ambient temperature and humidity, and the distance to the farthest coiler. Ask for a quotation stating dryer type and filtration grades explicitly, and whether a desiccant dryer is needed for the coating and storage conditions.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure at the farthest coiler during the first full production week.
- Send the supplier coiler, furnace and peening-line counts, coincident peak and farthest-coiler distance.
- Ask for dryer type and filtration grades in writing, and compare refrigerated against desiccant drying on total cost.
- Accept on a full-load test plus dew point and oil-aerosol checks, then survey pressure at the farthest coiler in week one.
Frequently asked questions
What pressure does a spring factory need?
A spring factory needs clean, dry air at 6 to 8 bar for wire coiling, heat treatment, shot peening, grinding and coating. Keep far-end pressure drop under 0.3 bar, because a pressure dip at the coiler changes spring pitch and spring rate, and size on the coincident peak of the coiling machines and the peening line.
Why must spring manufacturing air be dry?
Freshly peened spring steel rusts quickly, and a damp spring stored before coating develops surface rust that the coating cannot hide. A pre-filter, refrigerated dryer to a 3 degree C pressure dew point, 0.01 micron coalescing filter and carbon filter in series protect the coilers and peening nozzles, and a desiccant dryer to minus 20 degrees C helps in humid climates.
What size screw compressor does a spring factory need?
A mid-size spring plant with six to twelve coiling machines, two furnaces and one or two shot peening lines typically needs 4 to 8 cubic metres per minute at 6 to 8 bar, roughly a 30 to 55 kW screw compressor with a variable speed drive. The peening line alone can draw 2 to 4 cubic metres per minute, so count it honestly.
Related reading
- Screw Air Compressor Maintenance Checklist from a China Manufacturer
- How to Size a Screw Compressor: Air Demand Calculation Before You Buy from China
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.



