TL;DR — Direct answer: A firefighting equipment plant needs clean, dry air at 6 to 8 bar for extinguisher filling, hose coupling, valve assembly, hydrostatic testing and painting, with a dew point of minus 20 degrees C or lower and 0.01 micron filtration. Size on the coincident peak of the filling lines and the test bays, 4 to 8 cubic metres per minute, roughly a 30 to 55 kW screw compressor. QiAir, a Chinese screw compressor manufacturer and supplier, builds dry-air machines for firefighting equipment plants.

Firefighting equipment must work the first time it is used, often after years on a wall, and its factory builds that reliability into every cylinder, valve and hose. Extinguisher bodies are formed and welded, valves are machined and assembled, hoses are coupled and pressure tested, and every finished unit is filled, weighed and checked before it ships. Compressed air drives forming presses, welding clamps, filling stations, test rigs and paint guns. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for firefighting equipment plants are specified around dry air and stable pressure first.

Screw compressor installation
Screw compressor installation

The common sizing mistake is counting the assembly lines alone and forgetting filling and hydrostatic testing. Assembly lines draw air steadily, filling stations pulse at every cylinder, test bays draw heavy air during pressurising and draining, and drying stations need a long flow of very dry air after every test. This guide maps where the air goes, explains how to size for filling and test peaks, sets the dry-air standard that protects cylinders and valves, and shows what to put on a sizing sheet for a China supplier.

Where Air Is Used: Cylinders, Valves, Hoses and Filling

Cylinder forming and valve assembly are the heaviest users. Steel shells are spun and welded, valve bodies are machined and fitted with seals and springs, and hose couplings are crimped, using air for forming presses, welding clamps, machining centres and crimping tools, continuously while the lines run. A pressure dip at a crimping tool changes the coupling grip, and a hose coupling crimped loose can blow off under pressure when a firefighter needs it most. Valve springs and seals are fitted with air tools too, and a valve assembled with the wrong torque can stick closed or leak pressure over the years on the wall.

Filling, hydrostatic testing, drying, painting and final checks take the rest. Extinguishers are filled with powder or foam and pressurised, cylinders are hydrostatically tested and dried, valves are function tested, and bodies are painted and labelled. Test water left inside a cylinder rusts it from within, so drying air must be very dry and oil-free.

  • Cylinder forming and valves: forming presses, welding clamps, machining centres and seal fitting.
  • Hose coupling: crimping tools, pressure testing and coupling inspection stations.
  • Filling, testing and painting: powder and foam filling, hydrostatic rigs, blow-out drying and paint guns.

Sizing for Filling Lines and Hydrostatic Test Bays

List every line and bay with its flow at peak and at steady running. A mid-size plant with three to six assembly lines, two filling lines and a hydrostatic test area typically peaks at 4 to 8 cubic metres per minute at 6 to 8 bar, roughly a 30 to 55 kW screw compressor, with the peak landing when the filling lines run at full load while the test bays fill and drain together.

Keep the pressure drop to the farthest test bay under 0.3 bar at peak flow, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb filling and test spikes. Log pressure at the farthest test bay for a week of full production: that log is the honest record of whether the compressor is big enough.

  • Size on the coincident peak of the filling lines and the test bays, not on filling alone.
  • Use a variable speed drive for mixed steady and pulsing loads, and keep far-end pressure drop under 0.3 bar.
  • Log farthest-bay pressure during production for a week to prove the sizing in real use.

Very Dry Air: Preventing Internal Rust and Valve Damage

Moisture is the main enemy in firefighting equipment manufacturing. A cylinder dried with damp air rusts inside before it is filled, moisture in a valve causes sticking and seat damage, and damp powder clumps and will not discharge when the extinguisher is used. The fix is a treatment chain with extra drying: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, desiccant dryer to minus 20 degrees C for the drying stations, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour.

Oil is the second risk: oil inside an extinguisher contaminates the powder or foam, and oil on a valve seat changes its sealing and discharge behaviour. Keep the compressor room clean, ventilated and cool, drain condensate with automatic zero-loss drains, and test air at the farthest test bay quarterly. Change coalescing and desiccant elements on pressure drop and dew point, not on a calendar guess, since a spent desiccant bed is the most common cause of wet drying air.

  • Fit pre-filter, refrigerated dryer, desiccant dryer to minus 20 degrees C for drying stations, and 0.01 micron filtration.
  • Use a dedicated desiccant dryer branch for cylinder blow-out drying, separate from general shop air.
  • Drain condensate automatically, and test air at the farthest test bay quarterly for oil and moisture.

Buying from China: Sizing Sheet for a Firefighting Equipment Plant Compressor

QiAir is a Chinese manufacturer and supplier of screw air compressors, and a firefighting equipment order should start with a sizing sheet that names the line count. Send the supplier the number of assembly lines, filling lines and hydrostatic test bays, the coincident peak at 6 to 8 bar, the drying dew point the test bays require, ambient temperature and humidity, and the distance to the farthest test bay.

Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet and at the drying branch, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure and dew point at the farthest test bay during the first full production week.

  • Send the supplier assembly line, filling line and test bay counts, coincident peak, drying dew point and farthest-bay distance.
  • Ask for dryer type, desiccant branch and filtration grades in writing, with ISO 8573-1 class stated.
  • Accept on a full-load test plus dew point and oil-aerosol checks, then survey the farthest test bay in week one.

Frequently asked questions

What pressure does a firefighting equipment plant need?

A firefighting equipment plant needs clean, dry air at 6 to 8 bar for extinguisher filling, hose coupling, valve assembly, hydrostatic testing and painting. Keep far-end pressure drop under 0.3 bar, because a pressure dip changes hose crimping grip, and size on the coincident peak of the filling lines and the test bays.

How dry must air be for firefighting equipment manufacturing?

General shop air needs a refrigerated dryer to a 3 degree C pressure dew point, while cylinder blow-out drying needs a desiccant dryer to minus 20 degrees C or lower, with 0.01 micron filtration. Test water left inside a cylinder rusts it from within, and damp powder clumps and will not discharge when the extinguisher is used.

What size screw compressor does a firefighting equipment plant need?

A mid-size firefighting equipment plant with three to six assembly lines, two filling lines and a hydrostatic test area typically needs 4 to 8 cubic metres per minute at 6 to 8 bar, roughly a 30 to 55 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure and dew point at the farthest test bay under full load.

Related reading

QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.