TL;DR — Direct answer: A prefabricated building plant needs clean, dry air at 6 to 8 bar for steel framing, wall panel assembly, concrete moulding, insulation fitting and finishing, with a 3 degree C pressure dew point and 0.01 micron filtration. Size on the coincident peak of the framing lines and the panel lines, 8 to 15 cubic metres per minute, roughly a 55 to 110 kW screw compressor. QiAir, a Chinese screw compressor manufacturer and supplier, builds high-flow machines for prefabricated building plants.
A prefabricated building leaves the factory as finished wall panels, floor cassettes and steel frames, and its plant is a large hall where carpentry, steelwork and concrete meet. Steel frames are cut and welded, wall panels are assembled with insulation and sheathing, concrete elements are cast in moulds, and finished modules are finished, glazed and packed for transport. Compressed air drives nail guns, welding clamps, concrete vibrators, spray guns and handling tools. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for prefabricated building plants are specified around high flow and stable pressure first.

The common sizing mistake is counting the framing lines alone and forgetting concrete moulding and panel finishing. Framing lines draw air steadily, panel lines pulse at every nail gun and staple, concrete moulding draws heavy air during vibration and demoulding, and finishing lines use air for spraying and sealing. This guide maps where the air goes, explains how to size for framing and panel peaks, sets the dry-air standard that protects steel and finishes, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: Steel Frames, Wall Panels, Concrete and Finishing
Steel framing and wall panel lines are the heaviest users. Steel studs are cut and screwed into frames, wall panels are assembled with insulation, sheathing and membranes, and floor cassettes are built and braced, using air for nail guns, screw guns, staplers and clamps, continuously while the lines run. A pressure dip at a nail gun leaves fasteners proud, and a proud fastener shows through the finished wall surface of a home.
Concrete moulding, glazing, painting and module finishing take the rest. Concrete is poured into moulds and vibrated, panels are demoulded and cured, windows are glazed and sealed, and modules are painted and fitted out. Concrete dust and sawdust are everywhere, so valves and tools need filtration that survives them, and a compressor intake placed near the cutting saws will clog in days. Panel finishing also needs steady air for stapling insulation and sealing membranes, so a dip at a staple gun leaves a loose membrane that lets draughts and damp into the finished wall.
- Steel framing and panels: nail guns, screw guns, staplers and clamps running continuously.
- Concrete moulding: vibrators, demoulding air, mould cleaning and curing controls.
- Glazing, painting and finishing: window sealing, spray guns, fitting-out tools and module packing.
Sizing for Framing Lines and Panel Peaks
List every line, mould and bay with its flow at peak and at steady running. A mid-size plant with four to eight framing lines, two to four panel lines and a concrete moulding area typically peaks at 8 to 15 cubic metres per minute at 6 to 8 bar, roughly a 55 to 110 kW screw compressor, with the peak landing when the framing lines run at full load while the panel lines nail and staple together.
Keep the pressure drop to the farthest framing line under 0.3 bar at peak flow, and fit a receiver of 800 to 1500 litres per 10 cubic metres per minute to absorb nail gun and vibrator spikes. Log pressure at the farthest framing line for a week of full production: that log is the honest record of whether the compressor is big enough.
- Size on the coincident peak of the framing lines and the panel lines, not on framing alone.
- Use a variable speed drive for mixed steady and pulsing loads, and keep far-end pressure drop under 0.3 bar.
- Log farthest-line pressure during production for a week to prove the sizing in real use.
Dry Air for Steel Frames, Panels and Painted Finishes
Moisture is the main enemy in prefabricated building manufacturing. A steel frame assembled with damp air rusts inside the wall before the building is occupied, moisture in a spray gun leaves orange peel on a finished module, and damp air in a concrete mould causes surface defects on the panel. The fix is a treatment chain: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour, with a final point-of-use filter at each framing group and spray booth.
Dust is the second risk: concrete dust and sawdust drawn into a compressor intake clog filters and wear valves, and dust in a paint gun ruins a finished surface. Site the compressor intake away from cutting saws and concrete pouring, fit a heavy-duty intake filter and check it weekly, drain condensate with automatic zero-loss drains, and test air at the farthest framing line quarterly. Change coalescing elements on pressure drop, not on a calendar guess.
- Fit pre-filter, refrigerated dryer, 0.01 micron coalescing filter and carbon filter, with a final filter at each framing group and booth.
- Keep the compressor intake away from sawdust and concrete dust, with a heavy-duty pre-filter checked weekly.
- Drain condensate automatically, and test air at the farthest framing line quarterly for oil and moisture.
Buying from China: Sizing Sheet for a Prefabricated Building Plant Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and a prefabricated building order should start with a sizing sheet that names the line count. Send the supplier the number of framing lines, panel lines, concrete moulds and finishing bays, the coincident peak at 6 to 8 bar, the air-quality standard the framing lines and spray booths require, ambient temperature and humidity, and the distance to the farthest framing line.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure at the farthest framing line during the first full production week.
- Send the supplier framing line, panel line and mould counts, coincident peak and farthest-line distance.
- Ask for dryer type and filtration grades in writing, and compare oil-free against filtered oil-injected on total cost.
- Accept on a full-load test plus dew point and oil-aerosol checks, then survey pressure at the farthest line in week one.
Frequently asked questions
What pressure does a prefabricated building plant need?
A prefabricated building plant needs clean, dry air at 6 to 8 bar for steel framing, wall panel assembly, concrete moulding, insulation fitting and finishing. Keep far-end pressure drop under 0.3 bar, because a pressure dip leaves nail gun fasteners proud, and size on the coincident peak of the framing lines and the panel lines.
Why must prefabricated building air be dry?
A steel frame assembled with damp air rusts inside the wall before the building is occupied, moisture in a spray gun leaves orange peel on a finished module, and damp air in a concrete mould causes surface defects on the panel. A pre-filter, refrigerated dryer to a 3 degree C pressure dew point, 0.01 micron coalescing filter and carbon filter in series protect the steel, panels and finishes.
What size screw compressor does a prefabricated building plant need?
A mid-size prefabricated building plant with four to eight framing lines, two to four panel lines and a concrete moulding area typically needs 8 to 15 cubic metres per minute at 6 to 8 bar, roughly a 55 to 110 kW screw compressor with a variable speed drive. Add a 800 to 1500 litre receiver per 10 cubic metres per minute, and verify pressure at the farthest framing line under full load.
Related reading
- Single-Stage vs Two-Stage Screw Compressors: Which One a China Manufacturer Recommends
- Buying Screw Compressors from China: A Ranking Checklist for Choosing a Supplier
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.



