TL;DR — Direct answer: A sanitary ware and bathroom fixtures plant needs clean, dry air at 6 to 8 bar for ceramic casting, glazing, faucet machining, chrome plating, assembly and testing, with a 3 degree C pressure dew point and 0.01 micron filtration. Size on the coincident peak of the casting lines and the machining lines, 5 to 10 cubic metres per minute, roughly a 37 to 75 kW screw compressor. QiAir, a Chinese screw compressor manufacturer and supplier, builds dry-air machines for sanitary ware plants.
A bathroom fixture must look flawless and never leak, and its factory mixes ceramic craft with precision metalwork. Toilets and basins are cast in plaster moulds, glazed and fired, brass faucets are machined and chrome plated, and every finished piece is assembled, tested and packed. Compressed air drives casting machines, glazing guns, machining centres, plating lines and assembly tools. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for sanitary ware plants are specified around clean, dry air first.

The common sizing mistake is counting the casting lines alone and forgetting faucet machining and plating. Casting lines draw air steadily, glazing stations pulse at every spray, machining centres draw air at every tool change, and plating lines need clean air for drying and handling. This guide maps where the air goes, explains how to size for casting and machining peaks, sets the dry-air standard that protects glaze and chrome, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: Ceramic Casting, Glazing, Faucets and Plating
Ceramic casting and glazing are the heaviest users. Slip is poured into plaster moulds, pieces are demoulded and dried, glaze is sprayed in booths, and ware is fired in kilns, using air for casting machines, demoulding, spray guns and handling, continuously while the lines run. A pressure dip at a glazing gun changes the glaze thickness, and uneven glaze shows as a visible fault on a white basin that cannot be hidden.
Faucet machining, chrome plating, assembly, testing and packing take the rest. Brass bodies are machined on centres, parts are polished and chrome plated, cartridges and aerators are fitted, every faucet is pressure tested for leaks, and finished pieces are boxed. Plating air must stay free of oil and moisture, because a contaminated part plates badly and the chrome peels within months. Glazing booths also use air for cleaning moulds between casts, and a booth that loses pressure leaves glaze dust in the air that settles on wet glaze and ruins the finish.
- Ceramic casting and glazing: casting machines, demoulding, glaze spray guns and kiln handling.
- Faucet machining: machining centres, polishing stations, tool changes and chip blowing.
- Chrome plating, assembly and testing: plating line air, cartridge fitting, leak testing and packing.
Sizing for Casting Lines and Machining Peaks
List every line, booth and centre with its flow at peak and at steady running. A mid-size plant with three to six casting lines, four to eight machining centres and a glazing and plating area typically peaks at 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor, with the peak landing when the casting lines run at full load while the machining centres change tools together.
Keep the pressure drop to the farthest glazing booth under 0.3 bar at peak flow, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb glazing and tool change spikes. Log pressure at the farthest glazing booth for a week of full production: that log is the honest record of whether the compressor is big enough.
- Size on the coincident peak of the casting lines and the machining lines, not on casting alone.
- Use a variable speed drive for mixed steady and pulsing loads, and keep far-end pressure drop under 0.3 bar.
- Log farthest-booth pressure during production for a week to prove the sizing in real use.
Dry Air for Glaze, Chrome and Leak-Test Integrity
Moisture is the main enemy in sanitary ware manufacturing. A basin glazed with damp air shows pinholes in the glaze after firing, moisture in a chrome plating line causes poor adhesion and peeling, and damp air in a faucet leak test changes the pressure reading and hides a real leak. A clogged filter at a glazing booth is the most common cause of a slow pressure sag, so change elements on pressure drop, not on a calendar guess. The fix is a treatment chain: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour, with a final point-of-use filter at each glazing booth and machining group.
Oil is the second risk: oil on a ceramic surface stops glaze from wetting evenly, and oil on a brass part before plating causes chrome to blister. Keep the compressor room clean, ventilated and cool, drain condensate with automatic zero-loss drains, and test air at the farthest glazing booth quarterly. Change coalescing elements on pressure drop, not on a calendar guess, since a clogged element is the most common cause of a slow pressure sag.
- Fit pre-filter, refrigerated dryer, 0.01 micron coalescing filter and carbon filter, with a final filter at each glazing booth and machining group.
- Keep the compressor intake away from ceramic dust and plating fumes, with a heavy-duty pre-filter checked weekly.
- Drain condensate automatically, and test air at the farthest glazing booth quarterly for oil and moisture.
Buying from China: Sizing Sheet for a Sanitary Ware Plant Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and a sanitary ware order should start with a sizing sheet that names the line count. Send the supplier the number of casting lines, machining centres, glazing booths and plating lines, the coincident peak at 6 to 8 bar, the air-quality standard the glazing booths and plating lines require, ambient temperature and humidity, and the distance to the farthest glazing booth.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure at the farthest glazing booth during the first full production week.
- Send the supplier casting line, machining centre and booth counts, coincident peak and farthest-booth distance.
- Ask for dryer type and filtration grades in writing, and compare oil-free against filtered oil-injected on total cost.
- Accept on a full-load test plus dew point and oil-aerosol checks, then survey pressure at the farthest booth in week one.
Frequently asked questions
What pressure does a sanitary ware plant need?
A sanitary ware and bathroom fixtures plant needs clean, dry air at 6 to 8 bar for ceramic casting, glazing, faucet machining, chrome plating, assembly and testing. Keep far-end pressure drop under 0.3 bar at the glazing booths, because a pressure dip changes glaze thickness, and size on the coincident peak of the casting lines and the machining lines.
Why must sanitary ware manufacturing air be dry?
A basin glazed with damp air shows pinholes in the glaze after firing, moisture in a chrome plating line causes poor adhesion and peeling, and damp air in a faucet leak test changes the pressure reading and hides a real leak. A pre-filter, refrigerated dryer to a 3 degree C pressure dew point, 0.01 micron coalescing filter and carbon filter in series protect the glaze, chrome and test results.
What size screw compressor does a sanitary ware plant need?
A mid-size sanitary ware plant with three to six casting lines, four to eight machining centres and a glazing and plating area typically needs 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure at the farthest glazing booth under full load.
Related reading
- Single-Stage vs Two-Stage Screw Compressors: Which One a China Manufacturer Recommends
- Buying Screw Compressors from China: A Ranking Checklist for Choosing a Supplier
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.



