TL;DR — Direct answer: A medical device plant needs clean, dry, oil-free air at 6 to 7 bar for injection moulding, catheter extrusion, device assembly, leak testing and sterile packaging, with a dew point of minus 20 degrees C or lower and 0.01 micron filtration. Size on the coincident peak of the moulding lines and the assembly lines, 3 to 6 cubic metres per minute, roughly a 22 to 45 kW screw compressor. QiAir, a Chinese screw compressor manufacturer and supplier, builds oil-free machines for medical device plants.

A medical device is a small, precise product that goes into a hospital or a human body, and its factory is a clean, tightly controlled place. Plastic parts are injection moulded, catheters are extruded and tipped, devices are assembled under magnification, and every finished unit is leak tested, sterilised and sealed in sterile packaging. Compressed air drives moulding machines, extrusion lines, assembly tools, leak test rigs and packaging machines. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for medical device plants are specified around clean, oil-free air first.

QiAir screw air compressor unit
QiAir screw air compressor unit

The common sizing mistake is counting the moulding lines alone and forgetting assembly and leak testing. Moulding machines draw air steadily, extrusion lines pulse at every cut and tip, assembly stations draw air in short bursts, and leak test rigs need a long, stable flow for every device. This guide maps where the air goes, explains how to size for moulding and assembly peaks, sets the clean-air standard that protects devices and patients, and shows what to put on a sizing sheet for a China supplier.

Where Air Is Used: Moulding, Extrusion, Assembly and Leak Testing

Injection moulding and catheter extrusion are the steadiest users. Plastic housings, connectors and syringe barrels are moulded, catheters are extruded, tipped and cut to length, and tubing is formed and bonded, using air for mould clamping, ejection, extrusion cooling and cutting, continuously while the lines run. A pressure dip at a mould clamp changes part dimensions, and a connector moulded out of tolerance fails its fit check and scraps the whole run.

Device assembly, leak testing and sterile packaging take the rest. Components are assembled under magnification with air tools, catheters are bonded and inspected, every device is leak tested with clean air, and finished units are sealed in sterile pouches and boxed. Test air must stay free of oil and particles, because a device that fails a leak test after packaging has already cost the sterile pouch and the labour.

  • Injection moulding and extrusion: mould clamping, ejection, catheter extrusion, tipping and cutting.
  • Device assembly: air tools, bonding stations and inspection fixtures under magnification.
  • Leak testing and sterile packaging: clean-air leak rigs, pouch sealing, cartoning and case packing.

Sizing for Moulding Lines and Assembly Peaks

List every line, station and test rig with its flow at peak and at steady running. A mid-size plant with four to eight moulding machines, two to four extrusion lines and an assembly and test area typically peaks at 3 to 6 cubic metres per minute at 6 to 7 bar, roughly a 22 to 45 kW screw compressor, with the peak landing when the moulding machines cycle together while the leak test rigs run at full load.

Keep the pressure drop to the farthest moulding machine under 0.2 bar at peak flow, tighter than general industry, because mould clamps and ejection are sensitive to pressure change, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb moulding and test spikes. Log pressure at the farthest moulding machine for a week of full production: that log is the honest record of whether the compressor is big enough.

  • Size on the coincident peak of the moulding lines and the assembly lines, not on moulding alone.
  • Keep far-end pressure drop under 0.2 bar at the moulding machines, with a variable speed drive.
  • Log farthest-machine pressure during production for a week to prove the sizing in real use.

Oil-Free Clean Air: Protecting Devices, Catheters and Sterile Packs

Oil and particles are the two contaminants that ruin a medical device, and both are invisible until a device fails testing. A trace of oil on a catheter changes its surface and bonding, a particle in a moulded connector blocks a fit, and oil in a leak test rig gives a false reading that passes a faulty device. The fix is oil-free air at source: an oil-free screw compressor, a desiccant dryer to a minus 20 to minus 40 degree C pressure dew point, filtration to 0.01 micron with an activated-carbon filter for oil vapour, and a final point-of-use filter at each moulding machine and test rig.

Cleanroom discipline applies to the whole air system. Site the compressor outside the cleanroom in a separate ventilated room with its own filtered air supply, use stainless steel or coated pipework downstream of the final filter so rust cannot reach the lines, and test line air regularly for oil, moisture and particles. Keep the test results with the batch records for each device model, since auditors will ask for them during a quality system inspection.

  • Use an oil-free screw compressor for medical devices, where air contacts catheters, connectors and sterile packs directly.
  • Fit a desiccant dryer to minus 20 to minus 40 degrees C and 0.01 micron filtration, with a final filter at each machine and rig.
  • Use stainless or coated pipework after the final filter, and test line air regularly for oil, moisture and particles.

Buying from China: Sizing Sheet for a Medical Device Plant Compressor

QiAir is a Chinese manufacturer and supplier of screw air compressors, and a medical device order should start with a sizing sheet that names the line count. Send the supplier the number of moulding machines, extrusion lines, assembly stations and leak test rigs, the coincident peak at 6 to 7 bar, the air-quality class the moulding machines and test rigs require, ambient temperature and humidity, and the distance to the farthest moulding machine.

Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, a particle count at the final filter outlet, and an oil-aerosol check, with the ISO 8573-1 class confirmed in writing. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure and dew point at the farthest moulding machine during the first full production week.

  • Send the supplier moulding machine, extrusion line and test rig counts, coincident peak and farthest-machine distance.
  • Ask for an oil-free machine quotation with dryer type, filtration grades and ISO 8573-1 class in writing.
  • Accept on a full-load test plus dew point, particle count and oil-aerosol checks, then survey the farthest machine in week one.

Frequently asked questions

What pressure does a medical device plant need?

A medical device plant needs clean, dry, oil-free air at 6 to 7 bar for injection moulding, catheter extrusion, device assembly, leak testing and sterile packaging. Keep far-end pressure drop under 0.2 bar at the moulding machines, because a pressure dip changes part dimensions, and size on the coincident peak of the moulding lines and the assembly lines.

Why must medical device manufacturing air be oil-free?

A trace of oil on a catheter changes its surface and bonding, a particle in a moulded connector blocks a fit, and oil in a leak test rig gives a false reading that passes a faulty device. An oil-free screw compressor removes the oil risk at source, with a desiccant dryer to minus 20 degrees C or lower and 0.01 micron filtration downstream.

What size screw compressor does a medical device plant need?

A mid-size medical device plant with four to eight moulding machines, two to four extrusion lines and an assembly and test area typically needs 3 to 6 cubic metres per minute at 6 to 7 bar, roughly a 22 to 45 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure and dew point at the farthest moulding machine under full load.

Related reading

QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.