TL;DR — Direct answer: A gas cylinder and pressure vessel plant needs clean, dry air at 6 to 8 bar for shell forming, welding, heat treatment, hydrostatic testing, valve fitting and painting, with a dew point of minus 20 degrees C or lower and 0.01 micron filtration. Size on the coincident peak of the welding lines and the test bays, 5 to 10 cubic metres per minute, roughly a 37 to 75 kW screw compressor. QiAir, a Chinese screw compressor manufacturer and supplier, builds dry-air machines for pressure vessel plants.
A gas cylinder is a steel bottle that must hold pressure safely for decades, and its factory is a heavy fabrication shop with strict testing at every stage. Steel plate is formed into shells, heads are pressed and welded, vessels are heat treated, and every unit is hydrostatically tested, dried, fitted with valves and painted before delivery. Compressed air drives forming presses, welding clamps, test rigs, drying stations and paint guns. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for pressure vessel plants are specified around dry air and stable pressure first.

The common sizing mistake is counting the welding lines alone and forgetting hydrostatic testing and drying. Welding lines draw air steadily, forming presses pulse at every cycle, test bays draw heavy air during filling and draining, and drying stations need a long flow of very dry air after every test. This guide maps where the air goes, explains how to size for welding and test peaks, sets the dry-air standard that protects vessels and valves, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: Forming, Welding, Heat Treatment and Testing
Shell forming and welding are the heaviest users. Steel plate is rolled and pressed into shells, heads are formed, and circumferential and longitudinal seams are welded, using air for press clamping, part handling, welding positioners and seam tracking, continuously while the lines run. A pressure dip at a welding positioner changes seam alignment, and a misaligned seam means a weld that must be cut out and redone.
Heat treatment, hydrostatic testing, valve fitting, drying and painting take the rest. Furnaces use air for door controls and atmosphere valves, test bays use it for filling, pressurising and draining vessels, drying stations use it for blowing out test water, and valve lines use it for fitting, torqueing and leak checking. Test water left inside a vessel rusts it from within, so drying air must be very dry.
- Forming and welding: press clamping, part handling, welding positioners and seam tracking running continuously.
- Heat treatment: furnace door controls, atmosphere valves and cooling zone controls.
- Testing, drying and valves: hydrostatic filling and draining, blow-out drying, valve fitting and leak checking.
Sizing for Welding Lines and Hydrostatic Test Bays
List every line and bay with its flow at peak and at steady running. A mid-size plant with three to six welding lines, two to four forming presses and a hydrostatic test area typically peaks at 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor, with the peak landing when the welding lines run at full load while the test bays fill and drain together.
Keep the pressure drop to the farthest test bay under 0.3 bar at peak flow, and fit a receiver of 800 to 1500 litres per 10 cubic metres per minute to absorb press and test filling spikes. Log pressure at the farthest test bay for a week of full production: that log is the honest record of whether the compressor is big enough.
- Size on the coincident peak of the welding lines and the test bays, not on welding alone.
- Use a variable speed drive for mixed steady and pulsing loads, and keep far-end pressure drop under 0.3 bar.
- Log farthest-bay pressure during production for a week to prove the sizing in real use.
Very Dry Air: Preventing Internal Rust and Valve Damage
Moisture is the main enemy in pressure vessel manufacturing. A vessel dried with damp air rusts inside before it is valved, moisture in a valve causes sticking and seat damage, and damp air in a paint gun leaves orange peel on a cylinder. The fix is a treatment chain with extra drying: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, desiccant dryer to minus 20 degrees C for the drying stations, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour.
Oil is the second risk: oil inside a gas cylinder contaminates the gas it will carry, and oil on a valve seat changes its sealing. Keep the compressor room clean, ventilated and cool, drain condensate with automatic zero-loss drains, and test air at the farthest test bay quarterly. Change coalescing and desiccant elements on pressure drop and dew point, not on a calendar guess, since a spent desiccant bed is the most common cause of wet drying air.
- Fit pre-filter, refrigerated dryer, desiccant dryer to minus 20 degrees C for drying stations, and 0.01 micron filtration.
- Use a dedicated desiccant dryer branch for vessel blow-out drying, separate from general shop air.
- Drain condensate automatically, and test air at the farthest test bay quarterly for oil and moisture.
Buying from China: Sizing Sheet for a Pressure Vessel Plant Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and a pressure vessel order should start with a sizing sheet that names the line count. Send the supplier the number of welding lines, forming presses and hydrostatic test bays, the coincident peak at 6 to 8 bar, the drying dew point the test bays require, ambient temperature and humidity, and the distance to the farthest test bay.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet and at the drying branch, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure and dew point at the farthest test bay during the first full production week.
- Send the supplier welding line, press and test bay counts, coincident peak, drying dew point and farthest-bay distance.
- Ask for dryer type, desiccant branch and filtration grades in writing, with ISO 8573-1 class stated.
- Accept on a full-load test plus dew point and oil-aerosol checks, then survey the farthest test bay in week one.
Frequently asked questions
What pressure does a gas cylinder plant need?
A gas cylinder and pressure vessel plant needs clean, dry air at 6 to 8 bar for shell forming, welding, heat treatment, hydrostatic testing, valve fitting and painting. Keep far-end pressure drop under 0.3 bar, because a pressure dip at a welding positioner changes seam alignment, and size on the coincident peak of the welding lines and the test bays.
How dry must air be for pressure vessel manufacturing?
General shop air needs a refrigerated dryer to a 3 degree C pressure dew point, while vessel blow-out drying needs a desiccant dryer to minus 20 degrees C or lower, with 0.01 micron filtration. Test water left inside a vessel rusts it from within, and oil inside a gas cylinder contaminates the gas it will carry.
What size screw compressor does a pressure vessel plant need?
A mid-size pressure vessel plant with three to six welding lines, two to four forming presses and a hydrostatic test area typically needs 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor with a variable speed drive. Add a 800 to 1500 litre receiver per 10 cubic metres per minute, and verify pressure and dew point at the farthest test bay under full load.
Related reading
- How to Choose the Best Screw Air Compressor Manufacturer in China for Your Factory
- Two-Stage PM VFD Screw Compressors: How a Top China Supplier Cuts Factory Energy Costs
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.



