TL;DR — Direct answer: A vending machine plant needs clean, dry air at 6 to 8 bar for sheet metal work, cabinet foaming, cooling unit assembly, refrigerant charging, leak testing and final testing, with a 3 degree C pressure dew point and 0.01 micron filtration. Size on the coincident peak of the cabinet lines and the leak test stations, 5 to 10 cubic metres per minute, roughly a 37 to 75 kW screw compressor. QiAir, a Chinese screw compressor manufacturer and supplier, builds dry-air machines for vending machine plants.
A vending machine is a refrigerated cabinet with a payment system and a dispensing mechanism, and its factory builds that combination into every unit. Sheet metal cabinets are cut and folded, insulation is foamed between panels, cooling units are assembled and charged, and every finished machine is leak tested, run through a temperature check and tested for dispensing before delivery. Compressed air drives sheet metal tools, foaming fixtures, leak test rigs, charging stations and assembly tools. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for vending machine plants are specified around clean, dry air first.

The common sizing mistake is counting the cabinet lines alone and forgetting cooling units and leak testing. Cabinet lines draw air steadily, foaming stations pulse at every pour, leak test rigs need a long stable flow for every unit, and final testing uses air for dispensing checks and door sealing. This guide maps where the air goes, explains how to size for cabinet and test peaks, sets the dry-air standard that protects insulation and refrigerant circuits, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: Sheet Metal, Foaming, Cooling Units and Testing
Sheet metal work and cabinet foaming are the heaviest users. Steel sheets are cut, folded and welded into cabinets, foam is injected between panels for insulation, and doors are fitted with gaskets and glass, using air for presses, clamps, foaming fixtures and handling, continuously while the lines run. A pressure dip at a foaming fixture changes the foam density, and uneven foam leaves a cold bridge that sweats and rots the cabinet from inside.
Cooling unit assembly, charging, leak testing and final checks take the rest. Compressors and evaporators are mounted and piped, circuits are evacuated and charged with refrigerant, leak test rigs pressurise each unit and watch for decay, and finished machines are run through temperature pull-down and dispensing tests. Charging air must stay dry, because moisture in a refrigerant circuit forms acid that attacks the compressor from within.
- Sheet metal and foaming: presses, clamps, foaming fixtures and cabinet handling running continuously.
- Cooling unit assembly: mounting, piping, evacuation and refrigerant charging stations.
- Leak testing and final checks: pressure decay rigs, temperature pull-down and dispensing tests.
Sizing for Cabinet Lines and Leak Test Stations
List every line and station with its flow at peak and at steady running. A mid-size plant with three to six cabinet lines, two to four cooling unit lines and a charging and test area typically peaks at 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor, with the peak landing when the cabinet lines run at full load while the leak test rigs pressurise together.
Keep the pressure drop to the farthest leak test station under 0.2 bar at peak flow, tighter than general industry, because leak testing measures small pressure changes and a sagging supply gives false readings, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb foaming and test spikes. Log pressure at the farthest test station for a week of full production: that log is the honest record of whether the compressor is big enough.
Foaming stations create short, heavy air pulses, so the receiver and pipework matter as much as the compressor itself. A receiver placed near the foaming lines absorbs each pour without pulling pressure down at the leak test stations, and a ring main around the plant beats a single long branch line for keeping pressure even. Size the ring main for the foaming peak, not the average, and fit a pressure gauge at each test station so operators can see a supply problem before it ruins a leak test.
- Size on the coincident peak of the cabinet lines and the leak test stations, not on cabinets alone.
- Keep far-end pressure drop under 0.2 bar at the leak test stations, with a variable speed drive.
- Log farthest-station pressure during production for a week to prove the sizing in real use.
Dry Air for Insulation, Circuits and Refrigerant Integrity
Moisture is the main enemy in vending machine manufacturing. A cabinet foamed with damp air holds moisture in the insulation, moisture in a refrigerant circuit forms acid that attacks the compressor, and damp air in a leak test rig changes the pressure reading and hides a real leak. The fix is a treatment chain: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour, with a final point-of-use filter at each foaming group and test station.
Oil is the second risk: oil in a refrigerant circuit changes the oil balance of the compressor and shortens its life, and oil on a painted cabinet leaves a fisheye in the finish. Keep the compressor room clean, ventilated and cool, drain condensate with automatic zero-loss drains, and test air at the farthest test station quarterly. Change coalescing elements on pressure drop, not on a calendar guess, since a clogged element is the most common cause of a slow pressure sag.
- Fit pre-filter, refrigerated dryer, 0.01 micron coalescing filter and carbon filter, with a final filter at each foaming group and test station.
- Keep the compressor intake away from foaming fume and paint overspray, with a heavy-duty pre-filter checked weekly.
- Drain condensate automatically, and test air at the farthest test station quarterly for oil and moisture.
Buying from China: Sizing Sheet for a Vending Machine Plant Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and a vending machine order should start with a sizing sheet that names the line count. Send the supplier the number of cabinet lines, cooling unit lines, charging stations and leak test rigs, the coincident peak at 6 to 8 bar, the air-quality standard the foaming lines and test stations require, ambient temperature and humidity, and the distance to the farthest test station.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure at the farthest test station during the first full production week.
- Send the supplier cabinet line, cooling unit line and test rig counts, coincident peak and farthest-station distance.
- Ask for dryer type and filtration grades in writing, and compare oil-free against filtered oil-injected on total cost.
- Accept on a full-load test plus dew point and oil-aerosol checks, then survey pressure at the farthest station in week one.
Frequently asked questions
What pressure does a vending machine plant need?
A vending machine plant needs clean, dry air at 6 to 8 bar for sheet metal work, cabinet foaming, cooling unit assembly, refrigerant charging, leak testing and final testing. Keep far-end pressure drop under 0.2 bar at the leak test stations, because a sagging supply gives false leak readings, and size on the coincident peak of the cabinet lines and the leak test stations.
Why must vending machine manufacturing air be dry?
A cabinet foamed with damp air holds moisture in the insulation, moisture in a refrigerant circuit forms acid that attacks the compressor, and damp air in a leak test rig changes the pressure reading and hides a real leak. A pre-filter, refrigerated dryer to a 3 degree C pressure dew point, 0.01 micron coalescing filter and carbon filter in series protect the insulation, circuits and test results.
What size screw compressor does a vending machine plant need?
A mid-size vending machine plant with three to six cabinet lines, two to four cooling unit lines and a charging and test area typically needs 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure at the farthest test station under full load.
Related reading
- Screw Air Compressor Maintenance Checklist from a China Manufacturer
- How to Size a Screw Compressor: Air Demand Calculation Before You Buy from China
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.