TL;DR — Direct answer: An industrial robot plant needs clean, dry air at 6 to 8 bar for CNC machining, gear and joint assembly, painting, calibration and endurance testing, with a 3 degree C pressure dew point and 0.01 micron filtration. Size on the coincident peak of the machining centres and the assembly lines, 5 to 10 cubic metres per minute, roughly a 37 to 75 kW screw compressor with a variable speed drive. QiAir, a Chinese screw compressor manufacturer and supplier, builds machines with dry-air treatment for robot factories.
An industrial robot is a precision machine built from machined castings, gears, motors, controllers and cables, and its factory mixes heavy machining with delicate assembly. Robot arms are machined on CNC centres, gearboxes are assembled and tested, joints are fitted with motors and encoders, bodies are painted, and every finished robot is calibrated and run through endurance tests. Compressed air drives the machining centres, assembly tools, paint guns, calibration rigs and test stations. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for robot plants are specified around stable pressure and dry air first.

The common sizing mistake is counting the machining centres alone and forgetting assembly, painting and testing. Machining centres draw air in bursts at every tool change, assembly lines run steadily, the paint booth draws a constant flow while guns are open, and calibration rigs need clean, stable air for their measuring heads. This guide maps where the air goes, explains how to size for machining and assembly peaks, sets the clean-air standard that protects gearboxes and paintwork, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: CNC Machining, Gear Assembly, Painting and Calibration
CNC machining centres are the heaviest users. Robot arm castings and joint housings are milled, drilled and bored, using air for spindle cooling, tool changes, workpiece clamping and chip blowing, pulsing with every tool change and blow-off. A pressure dip at the spindle changes tool-change timing and can leave a tool half-seated, and a half-seated tool cuts a joint face out of tolerance. Fit a dedicated filter and regulator close to each machining group.
Gear and joint assembly, painting, calibration and testing take the rest. Gearboxes use air for bearing pressing, seal fitting and backlash testing, painting lines use it for spray guns and booth controls, calibration rigs use it for encoder testing and arm positioning, and endurance test stations use it for brake cycling and load simulation. Metal chips and paint overspray are everywhere, so valves need filtration that survives them.
- CNC machining: spindle cooling, tool changes, workpiece clamping and chip blowing pulsing with every cycle.
- Gear and joint assembly: bearing pressing, seal fitting, backlash testing and motor mounting.
- Painting, calibration and testing: spray guns, encoder testing, arm positioning and endurance test stations.
Sizing for Machining Bursts and Assembly-Line Demand
List every machine with its flow at peak and at steady running. A mid-size plant with six to twelve CNC machining centres, four to eight assembly lines, a paint booth and a calibration and testing area typically peaks at 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor, with the peak landing when the machining centres change tools together while the paint booth runs at full load.
Keep the pressure drop to the farthest machining centre under 0.3 bar at peak flow, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb tool-change and blow-off spikes. Log pressure at the farthest machining centre for a week of full production: that log is the honest record of whether the compressor is big enough.
- Size on the coincident peak of the machining centres and the assembly lines, not on machining alone.
- Use a variable speed drive for machining bursts, and keep far-end pressure drop under 0.3 bar.
- Log farthest-centre pressure during production for a week to prove the sizing in real use.
Dry Air for Gearboxes, Paintwork and Calibration Rigs
Moisture is the main enemy in robot manufacturing. A gearbox assembled with damp air rusts inside before it is sealed, moisture in a calibration rig causes measurement drift, and damp air in a paint gun leaves orange peel on a robot body. The fix is a treatment chain: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour, with a final point-of-use filter at each machining group and paint booth.
Oil is the second risk: oil on a painted robot body leaves a fisheye in the finish, and oil in a gearbox contaminates the grease and shortens bearing life. Keep the compressor room clean, ventilated and cool, drain condensate with automatic zero-loss drains, and test air at the farthest machining centre quarterly. Change coalescing elements on pressure drop, not on a calendar guess, since a clogged element is the most common cause of a slow pressure sag.
- Fit pre-filter, refrigerated dryer, 0.01 micron coalescing filter and carbon filter, with a final filter at each machining group and booth.
- Keep the compressor intake away from metal chips and paint overspray, with a heavy-duty pre-filter checked weekly.
- Drain condensate automatically, and test air at the farthest machining centre quarterly for oil and moisture.
Buying from China: Sizing Sheet for a Robot Factory Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and a robot factory order should start with a sizing sheet that names the machine count. Send the supplier the number of CNC machining centres, assembly lines and paint booths, the coincident peak at 6 to 8 bar, the air-quality standard the machining centres and paint guns require, ambient temperature and humidity, and the distance to the farthest machining centre. Ask for a quotation stating dryer type and filtration grades explicitly, and whether an oil-free machine or a filtered oil-injected machine fits the painting specification better.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure at the farthest machining centre during the first full production week.
- Send the supplier machining centre, assembly line and booth counts, coincident peak and farthest-centre distance.
- Ask for dryer type and filtration grades in writing, and compare oil-free against filtered oil-injected on total cost.
- Accept on a full-load test plus dew point and oil-aerosol checks, then survey pressure at the farthest centre in week one.
Frequently asked questions
What pressure does an industrial robot plant need?
An industrial robot plant needs clean, dry air at 6 to 8 bar for CNC machining, gear and joint assembly, painting, calibration and endurance testing. Keep far-end pressure drop under 0.3 bar, because a pressure dip at the machining centre can leave a tool half-seated and cut a joint face out of tolerance, and size on the coincident peak of the machining centres and the assembly lines.
Why must robot manufacturing air be dry?
A gearbox assembled with damp air rusts inside before it is sealed, moisture in a calibration rig causes measurement drift, and damp air in a paint gun leaves orange peel on a robot body. A pre-filter, refrigerated dryer to a 3 degree C pressure dew point, 0.01 micron coalescing filter and carbon filter in series protect the machining centres, gearboxes and paint booth.
What size screw compressor does a robot factory need?
A mid-size robot plant with six to twelve CNC machining centres, four to eight assembly lines, a paint booth and a calibration and testing area typically needs 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure at the farthest machining centre under full load.
Related reading
- Screw Air Compressor Maintenance Checklist from a China Manufacturer
- How to Size a Screw Compressor: Air Demand Calculation Before You Buy from China
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.