TL;DR — Direct answer: An adhesives and sealants plant needs clean, dry, oil-free air at 6 to 7 bar for mixing, dispersing, filling, capping and packing, with a 3 degree C pressure dew point and 0.01 micron filtration. Size on the coincident peak of the mixers and filling lines, 3 to 7 cubic metres per minute, roughly a 22 to 55 kW screw compressor with a variable speed drive. QiAir, a Chinese screw compressor manufacturer and supplier, builds oil-free machines for adhesives plants.
An adhesive or sealant is a chemical product, and its factory is a mixing and filling line. Resins, fillers and additives are dispersed in mixers, the batch is deaerated, and then it is filled into cartridges, tubes, pails and drums, capped, labelled and packed. Compressed air drives the mixer controls, filling nozzles, capping heads, labelling machines and drum handling equipment. A drop of oil contaminates a batch, moisture causes a sealant to skin over in the cartridge, and a pressure dip at the filler leaves a cartridge short. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for adhesives plants are specified around oil-free air first.

The common sizing mistake is treating an adhesives plant like a general chemical plant and buying a compressor with basic filtration. Mixers draw air steadily, filling lines pulse at every cartridge, drum handling draws heavy air in bursts, and deaeration systems need dry air on demand. This guide maps where the air goes, explains how to size for mixing and filling peaks, sets the oil-free standard that protects batches and cartridges, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: Mixing, Dispersing, Filling and Packing
Mixers and dispersers are the steadiest users. High-speed dispersers and planetary mixers use air for lid clamping, vacuum control, discharge valves and vessel cleaning, continuously while a batch runs. A batch that loses vacuum control traps air in the adhesive, and air bubbles in a sealant cartridge show up as gaps in the customer's joint. Keep pressure at the mixer within a narrow band, with a dedicated filter and regulator close to each mixing group.
Filling, capping, labelling and drum handling take the rest. Cartridge fillers use air for nozzle actuation, piston control and cut-off, capping heads use it for torque control, labelling machines use it for label application, and drum handling uses it for lifting, tilting and pumping. Resin and filler dust are present around the mixers, so valves need filtration that survives them.
- Mixing and dispersing: lid clamping, vacuum control, discharge valves and vessel cleaning running steadily.
- Filling and capping: nozzle actuation, piston control, cut-off and torque control pulsing with every cartridge.
- Labelling and drum handling: label application, drum lifting, tilting and pumping in bursts.
Sizing for Mixing Loads and Filling-Line Peaks
List every mixer and filling line with its flow at peak and at steady running. A mid-size plant with three to six mixers, two to four filling lines and a drum handling area typically peaks at 3 to 7 cubic metres per minute at 6 to 7 bar, roughly a 22 to 55 kW screw compressor, with the peak landing when the filling lines run at full speed while a mixer discharges. A variable speed drive follows the batch pattern of mixing and filling instead of loading and unloading a fixed-speed machine dozens of times a shift.
Keep the pressure drop to the farthest filling nozzle under 0.3 bar at peak flow, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb filler and drum-handling spikes. Log pressure at the farthest filling nozzle for a week of full production: that log is the honest record of whether the compressor is big enough.
- Size on the coincident peak of the mixers and the filling lines, not on mixing alone.
- Use a variable speed drive for batch mixing and filling loads, and keep far-end pressure drop under 0.3 bar.
- Log farthest-nozzle pressure during production for a week to prove the sizing in real use.
Oil-Free Air: Protecting Batches and Cartridges from Contamination
Oil in adhesives air is a product defect, not just a maintenance issue. A trace of oil carried into a resin batch changes the cure, oil in a filling nozzle contaminates the cartridge, and oil on a cartridge thread stops the cap from sealing. Moisture is the other risk: damp air in a moisture-cure sealant starts the cure inside the cartridge, and damp air in a mixer vacuum line leaves water in the batch. The standard is oil-free air at source: an oil-free screw compressor, a refrigerated dryer to a 3 degree C pressure dew point, and filtration to 0.01 micron, with a final point-of-use filter at each filling line.
Chemical fumes and dust need their own discipline. Keep the compressor intake away from the mixing hall so the machine does not breathe resin fumes or filler dust, fit a heavy-duty intake pre-filter, and check it weekly in the first months. Drain condensate with automatic zero-loss drains, and test air at the farthest filling nozzle quarterly.
- Use an oil-free screw compressor for adhesives and sealants, where air contacts the product directly.
- Fit refrigerated dryer to a 3 degree C pressure dew point and 0.01 micron filtration, with a final filter at each filling line.
- Keep the compressor intake away from resin fumes and filler dust, and test filling-line air quarterly.
Buying from China: Sizing Sheet for an Adhesives Plant Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and an adhesives order should start with a sizing sheet that names the line. Send the supplier the number of mixers and filling lines, the coincident peak at 6 to 7 bar, the air-quality class the product requires, ambient temperature and humidity, and the distance to the farthest filling nozzle. Ask for a quotation stating dryer type and filtration grades explicitly, and whether an oil-free machine is quoted, with the cost difference against a filtered oil-injected machine spelled out.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, and an oil-aerosol check at the final filter outlet, with an oil-free certificate where the product specification requires it. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure at the farthest filling nozzle during the first full production week.
- Send the supplier mixer and filling-line counts, coincident peak, product air-quality class and farthest-nozzle distance.
- Ask for an oil-free machine quotation with dryer type and filtration grades in writing.
- Accept on a full-load test plus dew point and oil-aerosol checks, then survey pressure at the farthest nozzle in week one.
Frequently asked questions
What pressure does an adhesives plant need?
An adhesives and sealants plant needs clean, dry, oil-free air at 6 to 7 bar for mixing, dispersing, filling, capping and packing. Keep far-end pressure drop under 0.3 bar, because a pressure dip at the filler leaves a cartridge short, and size on the coincident peak of the mixers and the filling lines.
Why must adhesives air be oil-free?
A trace of oil carried into a resin batch changes the cure, oil in a filling nozzle contaminates the cartridge, and oil on a cartridge thread stops the cap from sealing. An oil-free screw compressor removes the oil risk at source, with a refrigerated dryer to a 3 degree C pressure dew point and 0.01 micron filtration downstream.
What size screw compressor does an adhesives plant need?
A mid-size adhesives plant with three to six mixers, two to four filling lines and a drum handling area typically needs 3 to 7 cubic metres per minute at 6 to 7 bar, roughly a 22 to 55 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure at the farthest filling nozzle under full load.
Related reading
- Screw Air Compressor Maintenance Checklist from a China Manufacturer
- How to Size a Screw Compressor: Air Demand Calculation Before You Buy from China
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.