TL;DR — Direct answer: A powder metallurgy plant needs clean, dry air at 6 to 8 bar for powder mixing, compacting presses, sintering furnaces, sizing, machining and impregnation, with a 3 degree C pressure dew point and 0.01 micron filtration. Size on the coincident peak of the compacting presses and the finishing lines, 5 to 10 cubic metres per minute, roughly a 37 to 75 kW screw compressor with a variable speed drive. QiAir, a Chinese screw compressor manufacturer and supplier, builds dust-tolerant machines for powder metallurgy plants.
A powder metallurgy part starts as fine metal powder and leaves the plant as a gear, bearing or filter with near-net shape. Powder is mixed with lubricant, compacted in a die press, sintered in a furnace, sized or coined, machined where needed, and sometimes impregnated with oil. Compressed air drives the compacting presses, furnace controls, sizing presses, machining centres and packing lines. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for powder metallurgy plants are specified around dust tolerance and dry air first.

The common sizing mistake is counting the compacting presses alone and forgetting sintering, sizing and finishing. Compacting presses draw air in heavy bursts at every cycle, sintering furnaces are a steady control load, sizing presses pulse at every part, and machining centres draw air for tool changes and chip blowing. This guide maps where the air goes, explains how to size for press and finishing peaks, sets the dry-air standard that protects sintered parts, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: Powder Mixing, Compacting, Sintering and Sizing
Compacting presses are the heaviest users. Metal powder is pressed into shape in a die, using air for die filling, press clamping, part ejection and powder handling, with demand spiking at every cycle. A press that loses pressure mid-cycle produces a part with uneven density, and uneven density shows up later as a gear that wears early or a bearing that fails. Keep pressure at the press within a narrow band, since a dip of even 0.5 bar changes compaction force and part density.
Powder mixing, sintering, sizing, machining and impregnation take the rest. Mixers use air for discharge and cleaning, sintering furnaces use it for atmosphere controls, belt drives and cooling, sizing presses use it for coining and calibration, machining centres use it for tool changes and chip blowing, and impregnation lines use it for vacuum control and oil handling. Fine metal powder is everywhere, so valves need filtration that survives it.
- Compacting presses: die filling, press clamping, part ejection and powder handling pulsing with every cycle.
- Sintering furnaces: atmosphere controls, belt drives and cooling zones that need dry, stable air.
- Sizing, machining and impregnation: coining, calibration, tool changes, chip blowing and vacuum control.
Sizing for Compacting Press Bursts and Finishing Demand
List every press and machine with its flow at peak and at steady running. A mid-size plant with four to eight compacting presses, two sintering furnaces and a sizing and machining section typically peaks at 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor, with the peak landing when several presses cycle together while the finishing lines run at full load. A variable speed drive follows the press pattern instead of loading and unloading a fixed-speed machine dozens of times a shift.
Keep the pressure drop to the farthest compacting press under 0.3 bar at peak flow, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb press spikes. Log pressure at the farthest press for a week of full production: that log is the honest record of whether the compressor is big enough.
- Size on the coincident peak of the compacting presses and the finishing lines, not on presses alone.
- Use a variable speed drive for cyclic press loads, and keep far-end pressure drop under 0.3 bar.
- Log farthest-press pressure during production for a week to prove the sizing in real use.
Metal Powder Dust and Moisture: Protecting Parts and Equipment
Metal powder dust is the first problem in a powder metallurgy plant. Fine iron, copper and alloy powder is abrasive enough to score compressor internals, and a machine breathing it without protection loses capacity fast. Fit a heavy-duty intake pre-filter, clean it on a short cycle, and site the compressor in a separate ventilated room away from the press hall. A clogged intake is the most common cause of a slow capacity loss that looks like a sizing fault.
Moisture is the second risk: damp air rusts a sintered part before it is oiled or coated, moisture in a furnace control valve causes sticking, and oil contaminates a part surface before impregnation. The fix is a treatment chain: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour, with a final point-of-use filter at each press group. Drain condensate with automatic zero-loss drains, and test air at the farthest press quarterly.
- Protect the compressor intake from metal powder dust with a heavy-duty pre-filter and a separate compressor room.
- Fit pre-filter, refrigerated dryer, 0.01 micron coalescing filter and carbon filter, with a final filter at each press group.
- Drain condensate automatically, and test air at the farthest press quarterly for oil and moisture.
Buying from China: Sizing Sheet for a Powder Metallurgy Plant Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and a powder metallurgy order should start with a sizing sheet that names the press count. Send the supplier the number of compacting presses, sintering furnaces and sizing and machining machines, the coincident peak at 6 to 8 bar, the air-quality standard the presses and furnaces require, ambient dust level, and the distance to the farthest press. Ask for a quotation stating dryer type, filtration grades and the dust-tolerant intake package explicitly.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure at the farthest press during the first full production week.
- Send the supplier press, furnace and finishing machine counts, coincident peak and farthest-press distance.
- Ask for dryer type, filtration grades and the dust-tolerant intake package in writing.
- Accept on a full-load test plus dew point and oil-aerosol checks, then survey pressure at the farthest press in week one.
Frequently asked questions
What pressure does a powder metallurgy plant need?
A powder metallurgy plant needs clean, dry air at 6 to 8 bar for powder mixing, compacting presses, sintering furnaces, sizing, machining and impregnation. Keep far-end pressure drop under 0.3 bar, because a pressure dip at the press changes compaction force and leaves a part with uneven density, and size on the coincident peak of the presses and the finishing lines.
Why is metal powder dust a problem for compressors?
Fine iron, copper and alloy powder is abrasive enough to score compressor internals, and a machine breathing it without protection loses capacity fast. Fit a heavy-duty intake pre-filter, site the compressor in a separate ventilated room away from the press hall, and check the intake weekly in the first months.
What size screw compressor does a powder metallurgy plant need?
A mid-size powder metallurgy plant with four to eight compacting presses, two sintering furnaces and a sizing and machining section typically needs 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure at the farthest press under full load.
Related reading
- How to Choose the Best Screw Air Compressor Manufacturer in China for Your Factory
- Two-Stage PM VFD Screw Compressors: How a Top China Supplier Cuts Factory Energy Costs
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.