TL;DR — Direct answer: A pharmaceutical plant needs clean, dry, oil-free air at 6 to 7 bar for tablet pressing, granulation, sterile filling, cleanroom tools and packaging, with a dew point of minus 20 degrees C or lower and 0.01 micron filtration. Size on the coincident peak of the filling lines and the tablet presses, 4 to 8 cubic metres per minute, roughly a 30 to 55 kW screw compressor. QiAir, a Chinese screw compressor manufacturer and supplier, builds oil-free machines for pharmaceutical plants.
A pharmaceutical tablet starts as powder and ends as a sealed blister in a cleanroom, and every step in between depends on air that cannot carry oil, moisture or particles. Powders are granulated and blended, tablets are pressed and coated, liquids are filled into vials and ampoules, and finished packs are sealed, labelled and boxed. Compressed air drives tablet presses, granulators, filling nozzles, stoppering machines and packaging lines. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for pharmaceutical plants are specified around oil-free, dry air first.

The common sizing mistake is counting the tablet presses alone and forgetting sterile filling and packaging. Tablet presses draw air steadily, filling lines pulse at every nozzle and stopper, cleanroom tools draw air in short bursts, and packaging lines use air for carton handling and sealing. This guide maps where the air goes, explains how to size for filling and pressing peaks, sets the oil-free air standard that protects product and patients, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: Cleanrooms, Tablet Presses, Filling and Packaging
Tablet pressing and granulation are the steadiest users. Powders are blended and granulated, tablets are pressed in rotary machines, and coatings are sprayed in pans, using air for press ejection, granulator valves, spray nozzles and dust extraction, continuously while the lines run. A pressure dip at a tablet press changes ejection timing and tablet weight, and a tablet pressed wrong fails its weight and hardness check before it ever reaches a patient.
Sterile filling, cleanroom tools and packaging take the rest. Vials and ampoules are filled and stoppered under laminar flow, syringes are assembled and capped, cleanroom operators use air for gowning and tool cleaning, and packaging lines seal blisters, cartons and cases. Filling air must stay free of oil and particles, because a contaminated vial is a rejected batch that cannot be reworked.
- Tablet pressing and granulation: rotary presses, granulator valves, coating spray nozzles and dust extraction.
- Sterile filling: vial and ampoule filling, stoppering, syringe assembly and capping under laminar flow.
- Cleanroom tools and packaging: gowning air, tool cleaning, blister sealing, cartoning and case packing.
Sizing for Filling Lines and Tablet Press Peaks
List every line, press and filling station with its flow at peak and at steady running. A mid-size plant with two to four tablet lines, two sterile filling lines and a packaging area typically peaks at 4 to 8 cubic metres per minute at 6 to 7 bar, roughly a 30 to 55 kW screw compressor, with the peak landing when the filling lines run at full speed while the tablet presses cycle together.
Keep the pressure drop to the farthest filling line under 0.2 bar at peak flow, tighter than general industry, because filling nozzles and stoppering heads are sensitive to pressure change, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb filling spikes. Log pressure at the farthest filling line for a week of full production: that log is the honest record of whether the compressor is big enough.
- Size on the coincident peak of the filling lines and the tablet presses, not on pressing alone.
- Keep far-end pressure drop under 0.2 bar at the filling lines, with a variable speed drive for mixed loads.
- Log farthest-line pressure during production for a week to prove the sizing in real use.
Oil-Free Air and GMP-Grade Dryness: Protecting Product and Patients
Oil and moisture are the two contaminants that ruin a pharmaceutical batch, and both are invisible until a batch fails testing. A trace of oil in filling air contaminates a vial, moisture in a tablet press causes powder to stick and tablets to cap, and damp air in a cleanroom raises particle counts above the limit. The fix is oil-free air at source: an oil-free screw compressor, a desiccant dryer to a minus 20 to minus 40 degree C pressure dew point, filtration to 0.01 micron with an activated-carbon filter for oil vapour, and a final point-of-use filter at each filling line.
Cleanroom discipline applies to the whole air system. Site the compressor outside the cleanroom in a separate ventilated room with its own filtered air supply, use stainless steel pipework downstream of the final filter so rust cannot reach the lines, and test line air regularly for oil, moisture and particles. Keep the test results with the batch records for each product, since auditors will ask for them during a GMP inspection.
- Use an oil-free screw compressor for pharmaceutical production, where air contacts product, vials and tablets directly.
- Fit a desiccant dryer to minus 20 to minus 40 degrees C and 0.01 micron filtration, with a final filter at each filling line.
- Use stainless pipework after the final filter, and test line air regularly for oil, moisture and particles.
Buying from China: Sizing Sheet for a Pharmaceutical Plant Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and a pharmaceutical order should start with a sizing sheet that names the line count. Send the supplier the number of tablet lines, filling lines and packaging lines, the coincident peak at 6 to 7 bar, the air-quality class the filling lines and cleanroom require, ambient temperature and humidity, and the distance to the farthest filling line.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, a particle count at the final filter outlet, and an oil-aerosol check, with the ISO 8573-1 class confirmed in writing. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure and dew point at the farthest filling line during the first full production week.
- Send the supplier tablet line, filling line and packaging line counts, coincident peak and farthest-line distance.
- Ask for an oil-free machine quotation with dryer type, filtration grades and ISO 8573-1 class in writing.
- Accept on a full-load test plus dew point, particle count and oil-aerosol checks, then survey the farthest line in week one.
Frequently asked questions
What pressure does a pharmaceutical plant need?
A pharmaceutical plant needs clean, dry, oil-free air at 6 to 7 bar for tablet pressing, granulation, sterile filling, cleanroom tools and packaging. Keep far-end pressure drop under 0.2 bar at the filling lines, because a pressure dip changes filling volume, and size on the coincident peak of the filling lines and the tablet presses.
Why must pharmaceutical manufacturing air be oil-free?
A trace of oil in filling air contaminates a vial, moisture in a tablet press causes powder to stick and tablets to cap, and damp air in a cleanroom raises particle counts above the limit. An oil-free screw compressor removes the oil risk at source, with a desiccant dryer to minus 20 degrees C or lower and 0.01 micron filtration downstream.
What size screw compressor does a pharmaceutical plant need?
A mid-size pharmaceutical plant with two to four tablet lines, two sterile filling lines and a packaging area typically needs 4 to 8 cubic metres per minute at 6 to 7 bar, roughly a 30 to 55 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure and dew point at the farthest filling line under full load.
Related reading
- How to Choose the Best Screw Air Compressor Manufacturer in China for Your Factory
- Two-Stage PM VFD Screw Compressors: How a Top China Supplier Cuts Factory Energy Costs
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.