Site icon QiAir Compressor Manufacturer & Supplier in China

Best Screw Compressors for Gypsum Board Manufacturing: Dry Air for Forming, Cutting and Drying Lines

TL;DR — Direct answer: A gypsum board plant needs clean, dry air at 6 to 7 bar for the forming line, cutting, kiln drying controls and packing, with a 3 degree C pressure dew point and 0.01 micron filtration. Size on the coincident peak of forming and packing, 4 to 9 cubic metres per minute, roughly a 30 to 75 kW screw compressor with a variable speed drive. QiAir, a Chinese screw compressor manufacturer and supplier, builds dust-tolerant machines for gypsum board plants.

A gypsum board, or plasterboard, plant is a continuous line from calcined gypsum slurry to a finished board. Slurry is spread between two paper liners on a forming belt, edges are trimmed, the board is cut to length, dried in a kiln, then stacked and packed. Compressed air drives the forming line controls, cutting knives, kiln dampers, stacker and packing machines. A pressure dip at the cutter leaves a ragged edge, moisture corrodes a kiln valve, and gypsum dust chokes an unprotected compressor intake in weeks. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for gypsum board plants are specified around dust tolerance and dry air first.

QiAir screw air compressor
QiAir screw air compressor

The common sizing mistake is counting the forming line alone and forgetting packing and the kiln. Forming runs steadily, cutting pulses at every cut, kiln dampers move with the drying cycle, and the stacker draws heavy air in bursts. This guide maps where the air goes, explains how to size for forming and packing peaks, sets the dry-air standard that protects paper faces and valves, and shows what to put on a sizing sheet for a China supplier.

Where Air Is Used: Forming Line, Cutting, Kiln Drying and Packing

The forming line is the steadiest user. Air drives slurry mixer controls, belt tensioning, edge-forming guides and paper feed rollers, continuously while the line runs. A stop wastes a whole section of board, so pressure must stay stable: a dip moves the edge guide and leaves a wavy edge the trimmer cannot fix. Fit a dedicated filter and regulator close to the line.

Cutting, kiln drying and packing take the rest. Rotary and guillotine cutters use air for knife actuation and clamping, kilns use it for dampers and temperature-control valves, and stackers use it for suction cups, clamps and strapping. Gypsum dust is fine and everywhere, so valves need filtration that survives it.

Sizing for Forming-Line Peaks and Packing Bursts

List every line with its flow at peak and at steady running. A mid-size plant with one forming line, a cutting station, a drying kiln and a packing area typically peaks at 4 to 9 cubic metres per minute at 6 to 7 bar, roughly a 30 to 75 kW screw compressor, with the peak landing when the cutter fires as the stacker cycles. A variable speed drive follows the steady forming load plus cutting and packing bursts instead of loading and unloading a fixed-speed machine dozens of times a shift.

Keep the pressure drop to the farthest packing machine under 0.3 bar at peak flow, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb cutter and stacker spikes. Log pressure at the farthest packing machine for a week of full production: that log is the honest record of whether the compressor is big enough.

Gypsum Dust and Moisture: Protecting Paper Faces and Valves

Gypsum dust is the first problem in a plasterboard plant. Fine calcium sulphate dust coats everything near the forming line and cutters, and an unprotected intake clogs in weeks. Fit a heavy-duty intake pre-filter, clean it on a short cycle, and site the compressor in a separate ventilated room away from the forming hall. A clogged intake is the most common cause of a slow capacity loss that looks like a sizing fault.

Moisture is the second risk: damp air corrodes pneumatic valves, stains a paper face before drying, and oil marks the board surface. The fix is a treatment chain: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour, with a final point-of-use filter at the forming line. Drain condensate with automatic zero-loss drains and test air at the farthest machine quarterly.

Buying from China: Sizing Sheet for a Gypsum Board Plant Compressor

QiAir is a Chinese manufacturer and supplier of screw air compressors, and a gypsum board order should start with a sizing sheet that names the line. Send the supplier the forming line width and speed, cutting and kiln configuration, packing machine counts, coincident peak at 6 to 7 bar, the air-quality standard the forming line requires, ambient dust level, and the distance to the farthest packing machine. Ask for a quotation stating dryer type, filtration grades and the dust-tolerant intake package explicitly.

Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure at the farthest packing machine during the first full production week.

Frequently asked questions

What pressure does a gypsum board plant need?

A gypsum board plant needs clean, dry air at 6 to 7 bar for the forming line, edge trimming, cutting, kiln drying controls and stacking and packing. Keep far-end pressure drop under 0.3 bar, because a pressure dip at the cutting station leaves a ragged board edge, and size on the coincident peak of cutting and the stacker.

Why is gypsum dust a problem for compressors?

Fine gypsum dust coats everything near the forming line and cutters, and a compressor intake without protection clogs in weeks, causing a slow capacity loss that looks like a sizing fault. Fit a heavy-duty intake pre-filter, site the compressor in a separate ventilated room, and check the intake weekly in the first months.

What size screw compressor does a gypsum board plant need?

A mid-size gypsum board plant with one forming line, a cutting station, a drying kiln and a packing area typically needs 4 to 9 cubic metres per minute at 6 to 7 bar, roughly a 30 to 75 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure at the farthest packing machine under full load.

Related reading

QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.

Exit mobile version