TL;DR — Direct answer: A crane and heavy lifting plant needs clean, dry air at 6 to 8 bar for steel cutting and welding, hydraulic assembly, painting and load testing, with a 3 degree C pressure dew point and 0.01 micron filtration. Size on the coincident peak of the welding bays and the paint shop, 8 to 15 cubic metres per minute, roughly a 55 to 110 kW screw compressor. QiAir, a Chinese screw compressor manufacturer and supplier, builds high-flow machines for crane and heavy lifting plants.
A crane is a steel structure that lifts tonnes over people, and its factory is a large hall where heavy plate meets precision hydraulics. Steel plate is cut and welded into booms and girders, hydraulic cylinders and winches are assembled, electrical cabinets and cabs are fitted, and every finished crane is load tested before it leaves the yard. Compressed air drives plasma cutters, welding clamps, impact wrenches, paint guns and test rigs. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for crane plants are specified around high flow and stable pressure first.

The common sizing mistake is counting the welding bays alone and forgetting painting and load testing. Welding bays draw air steadily, hydraulic assembly pulses at every press and torque cycle, the paint shop draws a constant flow while guns are open, and load test areas need air for brake and control checks. This guide maps where the air goes, explains how to size for welding and painting peaks, sets the dry-air standard that protects hydraulics and paintwork, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: Steel Cutting, Welding, Hydraulics and Painting
Steel cutting and welding bays are the heaviest users. Heavy plate is cut by plasma and flame, girders are welded in jigs, and booms are assembled, using air for plasma torches, welding clamps, positioners, grinders and impact wrenches, continuously while the bays run. A pressure dip at a plasma torch changes cut quality, and a poor cut edge means extra grinding and a weld that must be reworked.
Hydraulic assembly, painting, cab fitting and load testing take the rest. Hydraulic cylinders use air for seal fitting, pressure testing and flushing, winches use it for assembly and brake checks, paint shops use it for spray guns and booth controls, and load test areas use it for control checks and safety device testing. Welding dust and paint overspray are everywhere, so valves need filtration that survives them.
- Steel cutting and welding: plasma torches, welding clamps, positioners, grinders and impact wrenches.
- Hydraulic assembly: seal fitting, cylinder pressure testing, flushing and winch brake checks.
- Painting and load testing: spray guns, booth controls, cab fitting and safety device testing.
Sizing for Welding Bays and Paint-Shop Demand
List every bay, booth and rig with its flow at peak and at steady running. A mid-size plant with four to eight welding bays, two hydraulic assembly lines, a paint shop and a load test yard typically peaks at 8 to 15 cubic metres per minute at 6 to 8 bar, roughly a 55 to 110 kW screw compressor, with the peak landing when the welding bays run at full load while the paint shop sprays. A second compressor or a larger receiver is cheaper than a line that stops every time the paint shop and the welding bays peak together, so size for that shared peak, not for either load alone.
Keep the pressure drop to the farthest welding bay under 0.3 bar at peak flow, and fit a receiver of 800 to 1500 litres per 10 cubic metres per minute to absorb plasma and impact wrench spikes. Log pressure at the farthest bay for a week of full production: that log is the honest record of whether the compressor is big enough.
- Size on the coincident peak of the welding bays and the paint shop, not on welding alone.
- Use a variable speed drive for mixed steady and pulsing loads, and keep far-end pressure drop under 0.3 bar.
- Log farthest-bay pressure during production for a week to prove the sizing in real use.
Dry Air for Hydraulics, Paintwork and Safety Controls
Moisture is the main enemy in crane manufacturing. A hydraulic cylinder assembled with damp air rusts inside before it is sealed, moisture in a paint gun leaves orange peel on a boom, and damp air in a load limiter causes slow or wrong readings. The fix is a treatment chain: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour, with a final point-of-use filter at each welding group and paint booth.
Oil is the second risk: oil in a hydraulic circuit contaminates the fluid and shortens seal life, and oil on a painted boom leaves a fisheye in the finish. Keep the compressor room clean, ventilated and cool, drain condensate with automatic zero-loss drains, and test air at the farthest welding bay quarterly. Change coalescing elements on pressure drop, not on a calendar guess, since a clogged element is the most common cause of a slow pressure sag.
- Fit pre-filter, refrigerated dryer, 0.01 micron coalescing filter and carbon filter, with a final filter at each welding group and booth.
- Keep the compressor intake away from welding fume and paint overspray, with a heavy-duty pre-filter checked weekly.
- Drain condensate automatically, and test air at the farthest welding bay quarterly for oil and moisture.
Buying from China: Sizing Sheet for a Crane Plant Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and a crane order should start with a sizing sheet that names the bay count. Send the supplier the number of welding bays, hydraulic assembly lines, paint booths and test areas, the coincident peak at 6 to 8 bar, the air-quality standard the hydraulic lines and paint guns require, ambient temperature and humidity, and the distance to the farthest welding bay.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure at the farthest welding bay during the first full production week.
- Send the supplier welding bay, hydraulic line and booth counts, coincident peak and farthest-bay distance.
- Ask for dryer type and filtration grades in writing, and compare oil-free against filtered oil-injected on total cost.
- Accept on a full-load test plus dew point and oil-aerosol checks, then survey pressure at the farthest bay in week one.
Frequently asked questions
What pressure does a crane plant need?
A crane and heavy lifting equipment plant needs clean, dry air at 6 to 8 bar for steel cutting and welding, hydraulic assembly, painting and load testing. Keep far-end pressure drop under 0.3 bar, because a pressure dip at a plasma torch changes cut quality, and size on the coincident peak of the welding bays and the paint shop.
Why must crane manufacturing air be dry?
A hydraulic cylinder assembled with damp air rusts inside before it is sealed, moisture in a paint gun leaves orange peel on a boom, and damp air in a load limiter causes slow or wrong readings. A pre-filter, refrigerated dryer to a 3 degree C pressure dew point, 0.01 micron coalescing filter and carbon filter in series protect the hydraulics, paintwork and safety controls.
What size screw compressor does a crane plant need?
A mid-size crane plant with four to eight welding bays, two hydraulic assembly lines, a paint shop and a load test yard typically needs 8 to 15 cubic metres per minute at 6 to 8 bar, roughly a 55 to 110 kW screw compressor with a variable speed drive. Add a 800 to 1500 litre receiver per 10 cubic metres per minute, and verify pressure at the farthest welding bay under full load.
Related reading
- Screw Compressor Heat Recovery: Turning Waste Heat into Factory Savings
- IoT Monitoring for Screw Compressor Rooms: A China Supplier's Practical Setup
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.