Site icon QiAir Compressor Manufacturer & Supplier in China

Best Screw Compressors for Commercial Refrigeration Equipment Manufacturing: Clean Air for Cabinets, Coils and Leak Testing

TL;DR — Direct answer: A commercial refrigeration plant needs clean, dry air at 6 to 7 bar for cabinet fabrication, coil brazing, compressor fitting, refrigerant charging, leak testing and foaming, with a 3 degree C pressure dew point and 0.01 micron filtration. Size on the coincident peak of the cabinet lines and the leak test stations, 4 to 8 cubic metres per minute, roughly a 30 to 55 kW screw compressor. QiAir, a Chinese screw compressor manufacturer and supplier, builds dry-air machines for commercial refrigeration plants.

A commercial refrigerator is a steel cabinet that must hold food at a steady temperature in a busy supermarket or kitchen, and its factory mixes sheet metal work with refrigeration assembly. Cabinets are cut, bent and foamed, evaporator and condenser coils are brazed, compressors are fitted and charged, and every finished unit is leak tested and run through a temperature check before shipping. Compressed air drives press brakes, brazing fixtures, leak test rigs, charging stations and assembly tools. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for commercial refrigeration plants are specified around clean, dry air first.

Industrial screw air compressor
Industrial screw air compressor

The common sizing mistake is counting the cabinet lines alone and forgetting coil brazing and leak testing. Cabinet lines draw air steadily, brazing stations pulse at every joint, leak test rigs need a long, stable flow for every unit, and foaming stations use air for fixtures and mould handling. This guide maps where the air goes, explains how to size for cabinet and test peaks, sets the dry-air standard that protects coils and refrigerant circuits, and shows what to put on a sizing sheet for a China supplier.

Where Air Is Used: Cabinets, Coils, Foaming and Leak Testing

Cabinet fabrication and foaming are the heaviest users. Sheet steel is cut, bent and welded into cabinets, foam is injected between inner and outer skins, and doors are fitted with gaskets and hinges, using air for press brakes, foaming fixtures, clamps and handling, continuously while the lines run. A pressure dip at a foaming fixture changes the foam density, and uneven foam leaves a warm spot that makes the compressor run all day.

Coil brazing, compressor fitting, charging, leak testing and packing take the rest. Copper coils are brazed in fixtures, compressors are mounted and piped, circuits are evacuated and charged with refrigerant, leak test rigs pressurise each unit and watch for decay, and finished cabinets are boxed for shipping. Charging air must stay dry, because moisture in a refrigerant circuit forms acid that attacks the compressor from within.

Sizing for Cabinet Lines and Leak Test Stations

List every line and station with its flow at peak and at steady running. A mid-size plant with three to six cabinet lines, two to four coil lines and a charging and test area typically peaks at 4 to 8 cubic metres per minute at 6 to 7 bar, roughly a 30 to 55 kW screw compressor, with the peak landing when the cabinet lines run at full load while the leak test rigs pressurise together.

Keep the pressure drop to the farthest leak test station under 0.2 bar at peak flow, tighter than general industry, because leak testing measures small pressure changes and a sagging supply gives false readings, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb foaming and test spikes. Log pressure at the farthest test station for a week of full production: that log is the honest record of whether the compressor is big enough.

Dry Air for Coils, Circuits and Foam Insulation

Moisture is the main enemy in commercial refrigeration manufacturing. A coil brazed with damp air oxidises inside the joint, moisture in a refrigerant circuit forms acid that attacks the compressor, and a cabinet foamed with damp air bonds poorly and delaminates. The fix is a treatment chain: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour, with a final point-of-use filter at each brazing group and test station.

Oil is the second risk: oil in a refrigerant circuit changes the oil balance of the compressor and shortens its life, and oil on a painted cabinet leaves a fisheye in the finish. Keep the compressor room clean, ventilated and cool, drain condensate with automatic zero-loss drains, and test air at the farthest test station quarterly. Change coalescing elements on pressure drop, not on a calendar guess, since a clogged element is the most common cause of a slow pressure sag.

Buying from China: Sizing Sheet for a Commercial Refrigeration Plant Compressor

QiAir is a Chinese manufacturer and supplier of screw air compressors, and a commercial refrigeration order should start with a sizing sheet that names the line count. Send the supplier the number of cabinet lines, coil lines, charging stations and leak test rigs, the coincident peak at 6 to 7 bar, the air-quality standard the brazing lines and test stations require, ambient temperature and humidity, and the distance to the farthest test station.

Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure at the farthest test station during the first full production week.

Frequently asked questions

What pressure does a commercial refrigeration plant need?

A commercial refrigeration plant needs clean, dry air at 6 to 7 bar for cabinet fabrication, coil brazing, compressor fitting, refrigerant charging, leak testing and foaming. Keep far-end pressure drop under 0.2 bar at the leak test stations, because a sagging supply gives false leak readings, and size on the coincident peak of the cabinet lines and the leak test stations.

Why must commercial refrigeration air be dry?

A coil brazed with damp air oxidises inside the joint, moisture in a refrigerant circuit forms acid that attacks the compressor, and a cabinet foamed with damp air bonds poorly and delaminates. A pre-filter, refrigerated dryer to a 3 degree C pressure dew point, 0.01 micron coalescing filter and carbon filter in series protect the coils, circuits and foam insulation.

What size screw compressor does a commercial refrigeration plant need?

A mid-size commercial refrigeration plant with three to six cabinet lines, two to four coil lines and a charging and test area typically needs 4 to 8 cubic metres per minute at 6 to 7 bar, roughly a 30 to 55 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure at the farthest test station under full load.

Related reading

QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.

Exit mobile version