TL;DR — Direct answer: A chain and sprocket plant needs clean, dry air at 6 to 7 bar for blanking, stamping, heat treatment, riveting, assembly and testing, with a 3 degree C pressure dew point and 0.01 micron filtration. Size on the coincident peak of the presses and assembly lines, 5 to 10 cubic metres per minute, roughly a 37 to 75 kW screw compressor. QiAir, a Chinese screw compressor manufacturer and supplier, builds machines with dry-air treatment for chain and sprocket factories.
A roller chain is made from hundreds of small, precise parts, and its factory is a press shop. Steel strip is blanked and stamped into link plates, pins and bushings are turned, parts are heat treated, and chains are assembled, riveted, pre-loaded and tested. Sprockets are cut, hobbed, heat treated and machined on the same site. Compressed air drives the blanking presses, assembly machines, riveting heads, testing rigs and packing lines. A pressure dip at the press leaves a link plate with a burr, moisture rusts a chain before it is oiled, and a weak riveting head leaves a pin loose. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for chain plants are specified around stable pressure and dry air first.

The common sizing mistake is counting the presses alone and forgetting assembly and testing. Blanking presses draw air in heavy bursts, assembly machines run steadily, riveting heads pulse at every pin, and testing rigs draw air for pre-loading and length measurement. This guide maps where the air goes, explains how to size for press and assembly peaks, sets the dry-air standard that protects chain steel, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: Blanking, Stamping, Riveting and Testing
Blanking and stamping presses are the heaviest users. High-speed presses cut link plates, pins and bushings from steel strip, using air for press clamping, feed control, scrap handling and die cooling, pulsing with every stroke. A press running at several hundred strokes a minute sees those pulses add up at the header, and a pressure dip changes blanking clearance and leaves a burr on the link plate. Burrs wear the chain out early in the customer's machine.
Assembly, riveting, heat treatment and testing take the rest. Chain assembly machines use air for part feeding, pin insertion and link handling, riveting heads use it for pin forming, heat treatment lines use it for furnace controls and quenching, and testing rigs use it for pre-loading, length measurement and fatigue testing. Metal swarf and stamping oil mist are everywhere, so valves need filtration that survives them.
- Blanking and stamping: press clamping, feed control, scrap handling and die cooling pulsing with every stroke.
- Assembly and riveting: part feeding, pin insertion and riveting heads that pulse at every pin.
- Heat treatment and testing: furnace controls, quenching, pre-loading rigs and length measurement.
Sizing for Press Strokes and Assembly-Line Demand
List every press and machine with its flow at peak and at steady running. A mid-size plant with six to twelve blanking presses, four to eight assembly machines and a heat treatment line typically peaks at 5 to 10 cubic metres per minute at 6 to 7 bar, roughly a 37 to 75 kW screw compressor, with the peak landing when the presses run at full speed while assembly lines are fully loaded. A variable speed drive follows the press pattern instead of loading and unloading a fixed-speed machine dozens of times a shift.
Keep the pressure drop to the farthest press under 0.3 bar at peak flow, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb press spikes. Log pressure at the farthest press for a week of full production: that log is the honest record of whether the compressor is big enough.
- Size on the coincident peak of the blanking presses and the assembly lines, not on presses alone.
- Use a variable speed drive for high-speed press loads, and keep far-end pressure drop under 0.3 bar.
- Log farthest-press pressure during production for a week to prove the sizing in real use.
Dry Air for Chain Steel: Preventing Rust Before Oiling
Moisture is the main enemy in chain manufacturing. A chain is oiled only at the end of the line, so bare steel parts sit exposed through blanking, assembly and testing, and damp air causes rust on link plates and pins before the chain ever reaches the oiling bath. The fix is a treatment chain: pre-filter, refrigerated dryer to a 3 degree C pressure dew point, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour, with a final point-of-use filter at each press group.
Stamping oil mist is the second problem: it coats filters and valves, and it carries into the air lines if the intake is near the press hall. Site the compressor in a separate ventilated room away from the presses, fit a heavy-duty intake pre-filter, and check it weekly in the first months. Drain condensate with automatic zero-loss drains, and test air at the farthest press quarterly. Change coalescing elements on pressure drop, not on a calendar guess.
- Fit pre-filter, refrigerated dryer, 0.01 micron coalescing filter and carbon filter, with a final filter at each press group.
- Site the compressor away from stamping oil mist, with a heavy-duty intake pre-filter checked weekly.
- Drain condensate automatically, and test air at the farthest press quarterly for oil and moisture.
Buying from China: Sizing Sheet for a Chain and Sprocket Plant Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and a chain order should start with a sizing sheet that names the press count. Send the supplier the number of blanking presses, assembly machines and riveting heads, the coincident peak at 6 to 7 bar, the air-quality standard the presses and riveting heads require, ambient temperature and humidity, and the distance to the farthest press. Ask for a quotation stating dryer type and filtration grades explicitly, and whether the compressor room package includes the intake filtration the stamping hall needs.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, and an oil-aerosol check at the final filter outlet. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure at the farthest press during the first full production week.
- Send the supplier press, assembly machine and riveting head counts, coincident peak and farthest-press distance.
- Ask for dryer type and filtration grades in writing, and confirm the intake package for the stamping hall.
- Accept on a full-load test plus dew point and oil-aerosol checks, then survey pressure at the farthest press in week one.
Frequently asked questions
What pressure does a chain and sprocket plant need?
A chain and sprocket plant needs clean, dry air at 6 to 7 bar for blanking, stamping, heat treatment, riveting, assembly and testing. Keep far-end pressure drop under 0.3 bar, because a pressure dip at the blanking press changes blanking clearance and leaves a burr on the link plate, and size on the coincident peak of the presses and the assembly lines.
Why must chain manufacturing air be dry?
A chain is oiled only at the end of the line, so bare steel parts sit exposed through blanking, assembly and testing, and damp air causes rust on link plates and pins before the chain reaches the oiling bath. A pre-filter, refrigerated dryer to a 3 degree C pressure dew point, 0.01 micron coalescing filter and carbon filter in series protect the presses and assembly machines.
What size screw compressor does a chain plant need?
A mid-size chain plant with six to twelve blanking presses, four to eight assembly machines and a heat treatment line typically needs 5 to 10 cubic metres per minute at 6 to 7 bar, roughly a 37 to 75 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure at the farthest press under full load.
Related reading
- Screw Compressor Heat Recovery: Turning Waste Heat into Factory Savings
- IoT Monitoring for Screw Compressor Rooms: A China Supplier's Practical Setup
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.