TL;DR — Direct answer: A battery energy storage system integration plant needs clean, dry air at 6 to 8 bar for cell handling, module and pack assembly, busbar fitting, liquid cooling connections and testing, with a dew point of minus 20 degrees C or lower and 0.01 micron filtration. Size on the coincident peak of the pack lines and the test stations, 5 to 10 cubic metres per minute, roughly a 37 to 75 kW screw compressor. QiAir, a Chinese screw compressor manufacturer and supplier, builds ultra-dry machines for battery storage plants.
A battery energy storage system is a container full of battery packs, inverters and cooling equipment, and its integration plant assembles cells into modules, modules into packs, and packs into racks and containers. Cells are handled, sorted and tested, modules are assembled with busbars and cooling plates, packs are wired and sealed, and every finished system is charged, discharged and tested before shipping to a solar or wind site. Compressed air drives the cell handling robots, assembly tools, torque wrenches, leak test rigs and packing lines. QiAir is a Chinese manufacturer and supplier of screw air compressors, and its machines for battery storage plants are specified around ultra-dry air first.

The common sizing mistake is counting the pack assembly lines alone and forgetting cell handling and testing. Cell handling robots draw air steadily, pack lines pulse at every torque cycle, leak test rigs draw air in bursts at every pack, and container fitting uses air for lifting and fastening. This guide maps where the air goes, explains how to size for pack and test peaks, sets the dry-air standard that protects cells and terminals, and shows what to put on a sizing sheet for a China supplier.
Where Air Is Used: Cell Handling, Pack Assembly, Cooling and Testing
Cell handling and pack assembly are the heaviest users. Robots move lithium cells between sorting, welding and assembly stations using air for vacuum grippers, clamps and linear drives, and pack lines use air for busbar fitting, torque wrenches, cooling plate mounting and enclosure sealing, pulsing with every torque cycle. A pressure dip at a torque wrench changes bolt preload, and a loose busbar bolt runs hot and fails in the field. Fit a dedicated filter and regulator close to each pack line.
Module assembly, liquid cooling, testing and container fitting take the rest. Module lines use air for cell stacking and welding controls, cooling systems use it for pipe fitting and leak testing, test stations use it for insulation testing and charge and discharge cycling, and container fitting uses it for rack installation, cable routing and door sealing.
- Cell handling and pack assembly: vacuum grippers, clamps, busbar fitting, torque wrenches and enclosure sealing.
- Module assembly and cooling: cell stacking, welding controls, pipe fitting and coolant leak testing.
- Testing and container fitting: insulation testing, charge cycling, rack installation and door sealing.
Sizing for Pack Lines and Test-Station Demand
List every line and station with its flow at peak and at steady running. A mid-size plant with four to eight pack assembly lines, two to four test stations and a container fitting area typically peaks at 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor, with the peak landing when the pack lines run at full speed while the test stations cycle together.
Keep the pressure drop to the farthest pack line under 0.3 bar at peak flow, and fit a receiver of 500 to 1000 litres per 10 cubic metres per minute to absorb torque and test spikes. Log pressure at the farthest pack line for a week of full production: that log is the honest record of whether the compressor is big enough.
- Size on the coincident peak of the pack lines and the test stations, not on pack lines alone.
- Use a variable speed drive for mixed cell handling and pack loads, and keep far-end pressure drop under 0.3 bar.
- Log farthest-line pressure during production for a week to prove the sizing in real use.
Ultra-Dry Air: Protecting Cells, Terminals and Cooling Circuits
Moisture is the main enemy in battery storage integration. Damp air inside a pack corrodes a cell terminal, moisture in a cooling connection causes a leak that shorts a module, and damp air in a torque wrench changes its calibration. The fix is a treatment chain with deep drying: pre-filter, desiccant dryer to a minus 20 to minus 40 degree C pressure dew point, coalescing filter to 0.01 micron, and activated-carbon filter for oil vapour, with a final point-of-use filter at each pack line.
Particles and oil need their own discipline. A particle in a cooling connection blocks coolant flow, and oil on a busbar joint raises its resistance so the joint runs hot. Use stainless steel or coated pipework downstream of the final filter so rust cannot reach the lines, drain condensate with automatic zero-loss drains, and test air at the farthest pack line quarterly for oil, moisture and particles.
- Fit pre-filter, desiccant dryer to minus 20 to minus 40 degrees C, 0.01 micron coalescing filter and carbon filter.
- Fit a final point-of-use filter at each pack line, and specify ISO 8573-1 Class 1 or 2 air in writing.
- Use stainless or coated pipework after the final filter, and test pack-line air quarterly for oil, moisture and particles.
Buying from China: Sizing Sheet for a Battery Storage Plant Compressor
QiAir is a Chinese manufacturer and supplier of screw air compressors, and a battery storage order should start with a sizing sheet that names the line count. Send the supplier the number of pack assembly lines, test stations and container fitting bays, the coincident peak at 6 to 8 bar, the air-quality class the pack lines and test stations require, ambient temperature and humidity, and the distance to the farthest pack line. Ask for a quotation stating dryer type and filtration grades explicitly, and whether a desiccant dryer to minus 40 degrees C is quoted.
Agree the acceptance test before shipment: a full-load run at rated pressure, a dew point reading at the dryer outlet, a particle count at the final filter outlet, and an oil-aerosol check, with the ISO 8573-1 class confirmed in writing. On arrival, install on a level plinth with clear cooler airflow, connect drains before the first run, and survey pressure and dew point at the farthest pack line during the first full production week.
- Send the supplier pack line, test station and fitting bay counts, coincident peak and farthest-line distance.
- Ask for a desiccant dryer quotation with filtration grades and ISO 8573-1 class in writing.
- Accept on a full-load test plus dew point, particle count and oil-aerosol checks, then survey the farthest line in week one.
Frequently asked questions
What pressure does a battery storage integration plant need?
A battery energy storage system integration plant needs clean, dry air at 6 to 8 bar for cell handling, module and pack assembly, busbar fitting, liquid cooling connections and testing. Keep far-end pressure drop under 0.3 bar, because a pressure dip at a torque wrench changes bolt preload and leaves a busbar bolt loose, and size on the coincident peak of the pack lines and the test stations.
How dry must air be for battery pack assembly?
Pack assembly air needs a desiccant dryer to a minus 20 to minus 40 degree C pressure dew point, with 0.01 micron filtration, targeting ISO 8573-1 Class 1 or 2 for oil and particles. Damp air inside a pack corrodes a cell terminal, and moisture in a cooling connection causes a leak that shorts a module.
What size screw compressor does a battery storage plant need?
A mid-size battery storage plant with four to eight pack assembly lines, two to four test stations and a container fitting area typically needs 5 to 10 cubic metres per minute at 6 to 8 bar, roughly a 37 to 75 kW screw compressor with a variable speed drive. Add a 500 to 1000 litre receiver per 10 cubic metres per minute, and verify pressure and dew point at the farthest pack line under full load.
Related reading
- Screw Compressor Heat Recovery: Turning Waste Heat into Factory Savings
- IoT Monitoring for Screw Compressor Rooms: A China Supplier's Practical Setup
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.