TL;DR — Direct answer: An asphalt mixing plant typically runs 7 to 8 bar, 6 to 12 m3/min, on 45 to 90 kW rotary screw compressors, with a 3°C pressure dew point dryer and 0.01 micron filtration protecting burners, baghouses and gates from dust and moisture. QiAir, a Chinese screw compressor manufacturer and supplier, sizes systems with receiver storage so pulse cleaning never starves the burner.
An asphalt mixing plant lives or dies on compressed air that never falters. The burner needs steady air for atomising fuel, the baghouse needs sharp pulses to clean its filter bags, and dozens of pneumatic gates and cylinders sequence aggregate, filler and bitumen through the mixer. When pressure sags, the flame wavers and the mix goes out of specification.

The environment makes the job harder than in a clean factory. Fine mineral dust hangs in the air around the dryer drum and the screening tower, summer heat pushes the compressor room past 40°C, and production runs in long shifts with no pause for a compressor trip. Sizing and filtration therefore matter as much as the compressor itself.
Burner Air and Aggregate Drying
The burner is the most pressure-sensitive load on the plant. It atomises heavy fuel oil or gas at 7 bar, and a drop of 0.5 bar changes the spray pattern enough to leave unburned fuel in the drum and cold spots in the aggregate. Operators then over-fire the burner to compensate, wasting fuel and pushing stack temperatures higher than the mix design allows.
Aggregate drying adds a large, steady air demand of its own. Pneumatic controls on the dryer drum, the cold feed bins and the vibrating screen all draw air continuously, and the total rises sharply when wet aggregate arrives after rain.
Fuel choice changes the air specification. Gas burners need clean, dry air for their control valves, while oil burners add a fuel pump and atomising air circuit that must stay free of water. In both cases a refrigerated dryer holding a 3°C pressure dew point protects the burner valves, and a coalescing filter keeps oil vapour out of the combustion air path.
- Hold 7 bar steady at the burner, never below 6.5 bar
- Size for wet aggregate surges, not dry-season averages
- Dry burner air to a 3°C pressure dew point
Baghouse Cleaning and Dust Control
The baghouse is the plant's biggest pulsed air consumer. Each pulse-jet valve fires a short, violent burst of compressed air down a filter bag to knock the dust cake off, and a large baghouse may fire a valve every few seconds all day. Those pulses add up to several cubic metres per minute, and they arrive as sharp spikes rather than a smooth flow.
Pulse timing decides whether the bags stay clean or blind over. If header pressure falls below 6 bar, the pulse weakens, dust stays on the bags, and differential pressure across the baghouse climbs until the fan cannot pull enough air through the drum.
A large receiver is the cheapest cure for pulse surges. A 3,000 to 5,000 litre vessel close to the baghouse absorbs each pulse without dragging the header down, and a dedicated branch line keeps the cleaning pulses from stealing air from the burner. Check the pulse valves for leaks every month, because one stuck valve can waste more air than a whole gate circuit.
- Fit a 3,000 to 5,000 litre receiver beside the baghouse
- Keep pulse pressure above 6 bar at the furthest valve
- Check pulse valves monthly for leaks and stuck diaphragms
Pneumatic Controls, Gates and Weighing
Every gate, flap and weighing hopper on an asphalt plant moves on air. Aggregate bins open and close on pneumatic cylinders, the filler silo feeds through air-operated slides, and the mixer discharge door must open and shut in seconds to keep the batch cycle tight. A slow cylinder stretches the cycle time, and over a shift that lost time becomes lost tonnes.
Weighing accuracy depends on stable air more than most operators realise. Pneumatic vibration on the weigh hoppers, air blowing across load cells and sticky gate cylinders all introduce weighing errors, and a 0.5 percent error on bitumen content can push a whole batch outside the road specification.
Dust is the enemy of every valve and cylinder on the plant. Fine filler dust works its way into valve spools and cylinder rods, scoring seals and causing slow leaks that grow over weeks. Fit 5 micron pre-filtration on the plant header, drain the receiver and filter bowls daily, and keep the compressor intake ducted away from the dustiest side of the site.
- Regulate gate air to a steady 6 bar at each manifold
- Drain receivers and filter bowls every shift
- Duct the compressor intake away from filler dust
Buying from China: Sizing Sheet for Asphalt Plants
Before requesting a quotation, gather four numbers: the burner air demand at full fire, the baghouse pulse count and air per pulse, the number of pneumatic gates and their simultaneous operation, and the distance from the compressor room to the baghouse and the burner. A supplier that quotes from the mixer capacity alone will undersize the air system and leave the plant short on its busiest days.
For most asphalt mixing plants the practical range is a 45 to 75 kW variable-speed drive screw compressor at 7.5 or 8 bar, with a refrigerated dryer, 0.01 micron filtration and a 3,000 to 5,000 litre receiver.
When comparing Chinese suppliers, ask for the full package price including dryer, filters, receiver and commissioning spares, and confirm the export packing, voltage and documentation for your country. Check the airend service interval, the availability of filters and separator elements through the supplier's export channel, and the hot-climate rating of the package. QiAir, a Chinese screw compressor manufacturer and supplier, quotes the complete package so buyers compare real installed cost.
- Collect burner, baghouse and gate loads before quoting
- Budget 45 to 75 kW VSD plus dryer, filters and receiver
- Confirm hot-climate rating, spares and export packing in writing
Frequently asked questions
What pressure does an asphalt mixing plant normally run?
Most run 7 to 8 bar at the header, with the burner held at 7 bar and baghouse pulses above 6 bar, so flame stability and bag cleaning stay consistent during peak production.
How much air does baghouse pulse cleaning use?
A large baghouse can consume several cubic metres per minute in pulses alone, arriving as sharp spikes. A 3,000 to 5,000 litre receiver beside the baghouse absorbs those spikes without dragging the header down.
Why does wet aggregate raise air demand?
Wet aggregate needs more burner firing and more pneumatic control cycling, and the dryer works harder to drive off the extra moisture. Air demand can rise by a third after rain, so size for wet conditions, not dry-season averages.
Should the burner and baghouse share one air line?
They can share one compressor room, but give the baghouse its own receiver and branch line, so cleaning pulses never steal pressure from the burner at full fire.
Related reading
- How to Choose the Best Screw Air Compressor Manufacturer in China for Your Factory
- Two-Stage PM VFD Screw Compressors: How a Top China Supplier Cuts Factory Energy Costs
QiAir is a Chinese manufacturer and supplier of screw air compressors. If you are sourcing a screw compressor from China — for a factory, a food plant, a construction site or a new production line — contact QiAir for a sized quotation, documented performance data and export support.